References to other locations in this manual are identified by an arrow and the speci‐ fied page number. In the electronic version of the manual, you can click the cross- reference to jump to the specified location. Example: See Ä ‘Cross-references’ on page 5. Hero Wash 300 TW moving head...
The load capacity of trusses or other fixtures must be suffi‐ cient for the intended number of devices. Not that the movement of the head places additional loads on the load-bearing parts. Hero Wash 300 TW moving head...
Page 8
Possible damage due to installation of a wrong fuse The use of different types of fuses can cause serious damage to the unit. Fire hazard! Only fuses of the same type may be used. Hero Wash 300 TW moving head...
For technological reasons, the light output of LEDs decreases over their lifetime. This effect increases with higher operating temperature. You can extend the service life of the illuminants by providing adequate ventilation and operating the LEDs with the lowest possible brightness. Hero Wash 300 TW moving head...
Possible data transmission errors For error-free operation make use of dedicated DMX cables and do not use ordinary microphone cables. Never connect the DMX input or output to audio devices such as mixers or amplifiers. Hero Wash 300 TW moving head...
Page 11
Safety cables are being threaded through the safety eyelets (B) on the bottom side of the housing. Please note that this device must not be connected to a dimmer. Hero Wash 300 TW moving head...
Connect the DMX output of the master device to the DMX input of the first slave device. Then connect the DMX output of the first slave device to the DMX input of the second slave device and so Hero Wash 300 TW moving head...
& PUSH PUSH DOWN 100-240V~50/ 60Hz max. 16A Hero Wash 300 TW Load: 260W ) * + , - . / 1 [DMX] LED lights up when the unit is controlled via a DMX controller. 2 [RUN] LED lights up when the device is in operation.
Page 14
Connections and controls 12 Fuse holder 13 [Power In] Lockable input socket (Power Twist) for mains power supply 14 [Power Out] Lockable output socket (Power Twist) for powering a connected device Hero Wash 300 TW moving head...
[UP] or [DOWN] briefly to turn it on again. This function can be activated / deactivated in the ‘Setting’ menu item. All previous settings are retained even when you switch the device off and discon‐ nect it from the mains. Hero Wash 300 TW moving head...
Press [UP] or [DOWN] to select the desired DMX mode and confirm the selec‐ tion with [SET]. The following DMX modes are available: Menu level 2 Description ‘DMX 13CH Mode’ 13-channel mode ‘DMX 19CH Mode’ 19-channel mode Hero Wash 300 TW moving head...
Page 17
To use a device as the master device, select one of the automatic programmes, acti‐ vate the sound control or the manual control. Connect the slave devices to the DMX output of the master device and select the DMX mode. Hero Wash 300 TW moving head...
Page 18
Segment 3 (0 to 100%). ‘ColorTemperature’ ‘OFF’ The setting of the intensity for warm white and cold white is done by setting the individual segments. ‘2500K…6100K’ Sets the colour temperature for all three segments. Hero Wash 300 TW moving head...
If the DMX control fails, the last setting is retained. ‘Blackout’ If the DMX control fails, the device is blacked out. ‘Auto Mode’ If the DMX control fails, the "Automatic programmes" mode is activated. Hero Wash 300 TW moving head...
Page 20
Blackout of the device ‘No’ Blackout off ‘If XY run’ Blackout during pan and tilt movements ‘PWM’ Pulse-width modulation ‘650Hz’ 650 Hz ‘1530Hz’ 1530 Hz ‘3600Hz’ 3600 Hz ‘12KHz’ 12 kHz ‘25KHz’ 25 kHz Hero Wash 300 TW moving head...
Page 21
‘Reset Motor’ ‘YES’ Motor reset is triggered. ‘NO’ The motor is not reset. ‘Factory ‘YES’ The device is reset to factory Reset’ default settings. ‘NO’ The device settings are not reset. Hero Wash 300 TW moving head...
Page 22
‘Dimmer’ ‘000…255’ Sets the initial dimmer intensity. ‘CW’ ‘000…255’ Sets the initial intensity for cold white. ‘WW’ ‘000…255’ Sets the initial intensity for warm white. ‘Zoom’ ‘-128…127’ Sets the initial setting for light focusing. Hero Wash 300 TW moving head...
Displays the total running time of the LED. ‘Current Mode’ Displays the current operating mode. ‘Temperature Head’ Displays the current head temperature. ‘Temperature Base’ Displays the current temperature of the device base. ‘Software Version’ Displays the current software version. Hero Wash 300 TW moving head...
Starting point Exponential Home Position Logarithmic Password Autolock S-Curve Ending point Fan Mode Zoom Test –128 –128 Automatic Reset Motor Silent TILT Blackout –128 Factory Reset If XY run 650Hz 1530Hz 3600Hz 12KHz 25KHz Hero Wash 300 TW moving head...
Page 26
Pan-Tilt auto programme 6 071…080 Pan-Tilt auto programme 7 081…090 Pan-Tilt auto programme 8 091…230 Sound control Pan and Tilt 231…240 Reset, if the value is transmitted for at least 3 seconds 241…255 No function Hero Wash 300 TW moving head...
Value Function 081…090 Pan-Tilt auto programme 8 091…230 Sound control Pan and Tilt 231…240 Reset, if the value is transmitted for at least 3 seconds 241…255 No function 7.9 Adjustable segments 3 3 3 Hero Wash 300 TW moving head...
Mounting options hanging, standing Dimensions (W × H × D) 310 mm × 390 mm × 208 mm Weight 10 kg Ambient conditions Temperature range 0 °C…40 °C Relative humidity 20 %…80 % (non-condensing) Hero Wash 300 TW moving head...
Page 31
Technical specifications Further information Type Wash Light output 285 W motorized zoom motorized focus rotating gobos static gobos Number of colour wheels Iris Prism Hero Wash 300 TW moving head...
The drawing below and the table show the pin assignment of a matching coupling. Assignment Ground (shielding) Signal inverted (DMX–, ‘cold’) Signal (DMX+, ‘hot’) unused / second connection (DMX–) unused / second connection (DMX+) Hero Wash 300 TW moving head...
DMX interface cir‐ cuit. If the procedures recommended above do not succeed, please contact our Service Center. You can find the contact information at www.thomann.de. Hero Wash 300 TW moving head...
Before cleaning, switch off the device and disconnect mains-oper‐ ated devices from the mains. Only use pH-neutral, solvent-free and non-abrasive cleaning agents. Clean the unit with a slightly damp lint-free cloth. Hero Wash 300 TW moving head...
Dispose of this device through an approved waste disposal firm or through your local waste facility. When discarding the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility. Hero Wash 300 TW moving head...