Table of Contents
Advertisement
Order no.: 627044000 ASC 55
Order no.: 627378000 ASC 145
etc.
Battery packs:
Order no.: 625367000 4.0 Ah (LiHD)
Order no.: 625368000 5.5 Ah (LiHD)
Order no.: 625369000 8.0 Ah (LiHD)
Order no.: 625026000 2.0 Ah (Li-Power)
Order no.: 625027000 4.0 Ah (Li-Power)
Order no.: 625028000 5.2 Ah (Li-Power)
etc.
For a complete range of accessories, see
www.metabo.com or the catalogue.
.
9. Mounting accessories
9.1
Mounting shoulder strap* (16) (p. 2 fig. A)
Can be attached to the metal eyelets (5) .
9.2
Mounting additional LED (22)
626982000 (p. 2 fig. B)
Place the silicone loop (28) around the hose and
hang it on the plastic hook (26) .
WARNING – To reduce the risk of injury,
read the operating instructions for the
additional LED (22) .
WARNING – Read all safety warnings,
instructions, illustrations and
specifications provided with the additional LED
(22) . Failures to respect the instructions can cause
injuries.
9.3
Mounting magnet* (29)
626980000 (p. 2 fig. B)
Screw onto thread (21) for magnet.
WARNING – To reduce the risk of injury,
read the supplementary sheet of the magnet
(29).
WARNING – Read all safety warnings,
instructions, illustrations and
specifications that can be found on the magnet
(29). Failures to respect the instructions can cause
injuries or damage.
9.4
Mounting adapter* (30) (only for TV 00)
626984000 (p. 3 fig. C)
Permits the use of a 500g screw-in cartridge. Screw
the adapter (30) onto the thread (31) and tighten it
with a suitable tool.
9.5
Mounting clamping coupling* (34)
626981000 (p. 3 fig. D)
Using a spanner*, remove the conical grease nipple
coupling (27) with a suitable tool, screw on the
clamping coupling* and tighten it with the tool.
*equipment-specific
10. Repairs
Repairs to electrical tools must only be carried
out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
11. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Packaging materials must be disposed of according
to their labelling in accordance with municipal
guidelines. Further information can be found at
www.metabo.com in the "Service" section.
Battery packs may not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Only for EU countries: never dispose of power
tools in your household waste! According to Euro-
pean Directive 2012/19/EU on Waste from Elec-
tric and Electronic Equipment and implementation in
national law, used power tools must be collected sepa-
rately and recycled in an environmentally-friendly
manner.
Discharge the battery pack in the power tool before
disposal. Prevent the contacts from short-circuiting (e.g.
by protecting them with adhesive tape).
12. Technical specifications
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
M
= dimensions: length x width x height
m
= weight
C
= screw-in cartridge capacity
c
The technical specifications quoted are subject to
tolerances (in compliance with relevant valid
standards).
Emission values
Using these values, you can estimate the
emissions from this tool and compare these with the
values emitted by other tools. The actual values
may be higher or lower, depending on the particular
application and the condition of the tool or
accessory. Please allow for breaks and periods
when the load is lower for assessment purposes.
Arrange protective measures for the user, such as
organisational measures based on the adjusted
estimates.
Vibration total value (vector sum of three directions)
determined in accordance with EN 62841:
L
= sound pressure level
pA
L
= acoustic power level
WA
K
, K
= measurement uncertainty
pA
WA
a
= vibration emission value
h
K
= uncertainty (vibration)
h
ENGLISH en
13
Advertisement
Table of Contents
