Use - Hoover HH74DBXP User Instructions

Porcelain/enamel : Good perfomance only with a thiny smooth, flat base.
Glass-ceramic : not recommended. Poor performance. May scratch
the surface.

6. USE

How to choose power management level
Through the "Power management" function, the user can set the
maximum power that can be reached by the hob. Power management
function is only available during first 30 seconds after switch on the
hob. There is even the possibility to repeat this setting switching off
and on the power plug. By setting the desired maximum power, the
hob automatically adjusts the distribution in the various cooking zones
so that this limit is never exceeded; with the added advantage of being
able to simultaneously manage all the zones without overload
problems. The customer can set the maximum power of hob between
2.5 kW and the maximum related power of the hob (this can change
according to the model). For example if the maximum power of the hob
is 7 kW, the maximum power level for setting is between 2.5kW and
7 kW. After connecting the appliance to the electrical power, within 30
seconds you can set the power level based on the points shown
below:
1.- Sw tch on hob.
2.- Let touch control f n sh ts n t al zat on process.
3.- Unlock the control.
P
8
8
4.- Before pass 30 seconds after switch on the hob; touch for 5 seconds
"-" key of timer.
8 8
8
8
5.- After th s moment, th s message w ll appear on d splay, Po on t mer
d splay. Power level d v ded by 100 n heater d splays.
P
0
6
6.- Using '+' and '-' of Timer keys, Power Management value can be
adjusted. When requ red value s selected, touch at the same t me "+"
and "–" keys dur ng 5 seconds.
P
0
4
7.- When th s process s f n shed, a long beep s heard and a reset s
produced. Start-up process w ll be generated aga n.
8 8
8
8
8.- After start-up process, n t mer d splay power management w ll be
showed.
P
0
4
8
8
8
8
0
5
0
5
8
8
0
5
07 GB
After that, touch control won´t allow any comb nat on wh ch
can exceed th s l m t.
Notes:
a) Th s power management s only ava lable dur ng f rst 30 seconds
after sw tch on the hob.
b) If th s power management select on s ON, f more than 90 seconds
after sw tch on the hob th s process w ll be f n sh w thout
any new power value were recorded.
c) If th s power management select on s ON, f any key s touched
except the comb nat on of t mer "+" and "–", process
w ll be f n sh w thout any new power value were recorded and touch
control w ll start work ng as usual, w thout reset.
d) If th s power management select on s ON, f any key s touched the
comb nat on of t mer "+" and "–", process w ll be
f n sh w th a new power value were recorded , reset and touch
control w ll start work ng as usual.
Switch ON/OFF a heater zone
8
8
To switch ON a heater Touch power key during 400 msec. Long beep
will be heard and "0" value will appear in target zone digit, indicating
power level.
1) If any cooking stage is in position 0, this display will switch OFF
automatically after 10 seconds and the zone OFF sequence will
sound.
2) If there is residual heat indication in the display which is ON but in 0
power, "0" will appear changing over.
3) If lock function is active you cannot switch ON a zone.
To switch OFF a heater Touch power key during 1,2 sec. 3 Short
beeps will be heard and nothing or "H" value will appear in target zone
digit if residual heat exists. Zone will be OFF.
1) If any cooking stage is in position 0, this display will switch OFF
automatically after 10 seconds and the zone OFF sequence will
sound.
2) If there is residual heat indication in the display which is OFF, "H"
will be displayed.
3) Even lock function is active you can switch OFF a zone.
4) If only one heater is active and this one is switched off, 4 Short beep
will be heard indicating all cook top is Off.
Increase / Decrease power level
8
8
With a short press on '+' or '-' keys, Increase or decrease power in the
selected zones digit: 0-1-2-3...9-P
1. For Long Presses in + or - keys, power level increases /decreases
continuously. With a fast increase, power stops at level 9, and for a
higher power another short press is needed on the + key. No beep
sound is heard with fast increase / decrease.
2. Once arrived to P power level, pressing + key again does not
change power level to 0.Once arrived to 0 power level, pressing - key
again does not change power level to P.
3. With a zone ON at 0 power level, if the zone is hot, 0 will blink
alternatively. After 10 seconds, 0 will disappear an 'H' letter will appear
fixed on display.
4. When a heater is selected and '+' & '-'keys are touched at the same
time, power level will go to '0' but heater will maintain selected during
10 seconds. If heater was temporized, timer will go to Off. This action
can only be developed in several cases depending touch control
configuration.The following examples are for information only.
Personal experience should then let you adapt these settings to your
taste and habits.
8
8
8
8