Page 1
Please use this service manual with referring to the ● 修理の際は、必ず取扱説明書を参照の上、作業を行っ ● operating instructions without fail. てください。 Some illustrations using in this service manual are ● 本文中に使用しているイラストは、説明の都合上現物 ● slightly different from the actual set. と多少異なる場合があります。 TOKYO, JAPAN Denon Brand Company, D&M Holdings lnc. X0334V.02 DE/CDM 0704...
Page 2
DVM-2845CI SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check.
DVM-2845CI Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, and wires have been returned to their original positions. Afterwards, do the following tests and confirm the specified values to verify compliance with safety standards.
DVM-2845CI STANDARD NOTES FOR SERVICING Circuit Board Indications Pb (Lead) Free Solder 1. The output pin of the 3 pin Regulator ICs is When soldering, be sure to use the Pb free solder. indicated as shown. How to Remove / Install Flat Pack-IC...
Page 6
DVM-2845CI 3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron: be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from pin or the solder lands under the IC when all pins of the flat pack-IC.
DVM-2845CI With Iron Wire: 2. Installation 1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA...
DVM-2845CI Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.
DVM-2845CI CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart REMOVAL REMOVE/*UNHOOK/ LOC. PART Fig. This flowchart indicates the disassembly steps to gain UNLOCK/RELEASE/ Note access to item(s) to be serviced. When reassembling, UNPLUG/DESOLDER follow the steps in reverse order. Bend, route, and dress the cables as they were originally.
DVM-2845CI Reference Notes (L-1) CAUTION 1: Locking Tabs (L-1) are fragile. Be careful not to break them. 1-1. To release eight Locking Tabs (L-1), first release (L-1) five Locking Tabs (A), and then three Locking Tabs (B). (Fig. D2) CAUTION 2: Electrostatic breakdown of the laser...
Page 11
DVM-2845CI Screw A Chuck arm [5] Slide Tray Assembly Rotary tray washer Rotary tray spring Rotary tray washer CN2103 (S-4) Turn Slide Tray Assembly (L-2) [7] Power SW CBA Short the three short lands by soldering. (L-2) Slide Tray CN2201 (Either of two places.)
Page 13
DVM-2845CI (S-16) [21] DVD Main CBA Unit [22] PCB Holder Fig. D10...
Page 14
DVM-2845CI SLIDE TRAY ASSEMBLY DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart This flowchart indicates the disassembly steps to gain access to item(s) to be serviced. When Reassembly, follow the steps in reverse order. Bend, route, and dress the cables as they were originally.
Page 15
DVM-2845CI 2. Disassembly Method Reference Notes 1. Disassembly note REMOVAL Slide the Rotary Tray slowly in the direction of the REMOVE/*UNHOOK/ PART Fig. front while rotating it. UNLOCK/RELEASE/ Note .No. UNPLUG/DESOLDER 2. Reassembly note Align the rails on the Rotary Tray with the slot on...
Page 16
DVM-2845CI (S-1) Slide Tray [1] Chuck Arm (P-1) Clamper (W-1) (W-1) Yoke Magnet [8] Mecha Desolder Cable [9] Detector Switch Lead Desolder (S-8) clamper [10] Rotary Motor Assembly Fig. MD1 [6] Belt L [7] Gear Plate (S-6) (S-6) (S-7) (S-6)
Page 17
DVM-2845CI [13] Rotary Slide Tray CN5005 CN5003 Stopper [15] Motion Pin B Gear Slot A (P-2) Pin D turn [12] Slot Lever Slot B Pin C Slot C Pin E [14] Mecha Holder Assembly (S-9) (S-9) Pin E [11] Relay CBA + Sensor CBA...
DVM-2845CI TROUBLESHOOTING FLOW CHART NO.1 FLOW CHART NO.1 The power cannot be turned on. The power cannot be turned on. Is the fuse normal? Is the fuse normal? See FLOW CHART No.2 <The fuse blows out.> See FLOW CHART No.2 <The fuse blows out.>...
Page 20
DVM-2845CI FLOW CHART NO.6 P-ON+10V (EV+10V) is not outputted. Check D1030, C1035, C1048, L1009 and Is 10V voltage supplied to the emitter of Q1002? the periphery circuit, and service it if defective. Check Q1016 and service it if defective. Is the voltage of base on Q1002 lower than the voltage of emitter on Q1002 when turning the power on? Replace Q1002.
Page 21
DVM-2845CI FLOW CHART NO.12 The fluorescent display tube does not light up. Is 3.3V voltage supplied to Pin(13) and Check the P-ON+3.3V line and service it if defective. Pin(43) of IC2001? Is the voltage of approximately -24V to -28V Check the -FL line and service it if defective.
Page 22
DVM-2845CI FLOW CHART NO.14 No operation is possible from the remote control unit. Operation is possible from the DVD, but no operation is possible from the remote control unit. Check CHG+5V line and service it if defective. Is 5V voltage supplied to the Pin(3) terminal of the infrared remote control receiver (RM2001)? Is the "L"...
Page 23
DVM-2845CI FLOW CHART NO.18 [No Disc] indicated. (When the focus servo is not functioning.) Replace the DVD Main CBA Unit. No improvement can be found. Original DVD Main CBA Unit is poor. Replace the DVD Mechanism. FLOW CHART NO.19 [No Disc] indicated. (When the laser beam does not light up.) Replace the DVD Main CBA Unit.
Page 24
DVM-2845CI FLOW CHART NO.21 Picture does not appear normally. Set the disc on the disc tray, and playback. Replace the DVD Main CBA Unit or DVD Mechanism. Are the video signals outputted to each pin of CN1601 on the AV CBA?
Page 25
DVM-2845CI FLOW CHART NO.22 Audio is not outputted. Set the disc on the disc tray, and playback. Replace the DVD Main CBA Unit or DVD Mechanism. Are the analog audio signals outputted to each pin of CN1601 on AV CBA?
Page 26
DVM-2845CI FLOW CHART NO.23 Rotary tray does not function. Is the normal control voltage inputted to pins Check the switches (SW2208, 2209, 2211 - 2214) (39, 40, 41) of IC3001? For each terminal voltage, and their periphery, and service it if defective.
DVM-2845CI SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
Page 36
DVM-2845CI LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQES D'INCELE N'UTILISER QUE DES FUSIBLE DE MÊME TYPE.
Page 37
DVM-2845CI DVD Main 1/8 Schematic Diagram 1 NOTE: Either IC461 or IC462 is used for DVD MAIN CBA UNIT.
Page 38
DVM-2845CI DVD Main 2/8 Schematic Diagram...
Page 39
DVM-2845CI IC101 Voltage Chart ~ : Voltage is not consistent ----- : Not used Unit : Volts PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY...
Page 40
DVM-2845CI DVD Main 3/8 Schematic Diagram...
Page 41
DVM-2845CI DVD Main 4/8 Schematic Diagram...
Page 42
DVM-2845CI DVD Main 5/8 Schematic Diagram...
Page 43
DVM-2845CI DVD Main 6/8 Schematic Diagram...
Page 44
DVM-2845CI DVD Main 7/8 Schematic Diagram...
Page 45
DVM-2845CI DVD Main 8/8 Schematic Diagram...
Page 46
DVM-2845CI AV 1/2 Schematic Diagram CAUTION ! CAUTION ! For continued protection against fire hazard, Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. NOTE: replace only with the same type fuse. If Main Fuse (F1001) is blown , check to see that all components in the power supply...
DVM-2845CI FIRMWARE RENEWAL MODE 1. Turn the power on and remove the disc on the tray. 5. After programming is finished, the tray opens auto- 2. To put the DVD player into version up mode, press matically. Fig. e appears on the screen and the [9], [8], [7], [6], and [SEARCH MODE] buttons on checksum in (*2) of Fig.
DVM-2845CI LEAD IDENTIFICATIONS 2SK3498 2SA1015-Y(TE2 F T) 2SC1815-(GR)(TE2 F T) KRA110M-AT/P 2SA966-Y(TE6 F M) KRC110M-AT/P KTC3205-Y-AT/P KTA1266-Y-AT/P KTA1273-Y-AT/P KTA1267-Y-AT/P KTC3199-GR-AT/P G D S E C B E C B LD1117V PT204-6B-12 M38503G4A-131FP UZ1086L-ADJ BA6956AN 1: Vin 2: Vo 3: GND...
Page 58
DVM-2845CI PARTS LIST OF EXPLODED VIEW (CABINET1) *本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. * "nsp" 印の部品は常時在庫していませんので供給に長時間を要することがあります。場合によっては、供給をお断りする場合があります。 * Part indicated with the mark “nsp” are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused.
Page 59
DVM-2845CI Ref. No. Part No. Part Name Remark Q'ty 2L012 SCREW TAP TIGHT M3X5 BIND GBHC3050 HEAD+BLK NI 2L021 SCREW TAP TIGHT M3X5 BIND GBHC3050 HEAD+BLK NI 2L031 SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080 2L032 SCREW P-TIGHT M3X8 BIND HEAD+...
Page 60
DVM-2845CI PARTS LIST OF EXPLODED VIEW OF SLIDE MECHANISM UNIT (CABINET2) *本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. * "nsp" 印の部品は常時在庫していませんので供給に長時間を要することがあります。場合によっては、供給をお断りする場合があります。 * Part indicated with the mark “nsp” are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused.
Page 62
DVM-2845CI NOTE : Apply some grease to the Fill Color position. Chief Ingredient of FAG-102R - Hydrocarbon synthetic oil - Lithium soap - Additives...
DVM-2845CI PARTS LIST OF PACKING & ACCESSORIES *本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. * "nsp" 印の部品は常時在庫していませんので供給に長時間を要することがあります。場合によっては、供給をお断りする場合があります。 * Part indicated with the mark “nsp” are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused.