Download Print this page

Advertisement

Quick Links

Quick Start
G
S
ETTING
TARTED
The NetVanta 5660 is configured using the command line interface (CLI). Entering a
question mark (?) at the command prompt displays contextual help and all commands
available from that prompt.
This NetVanta unit ships with a statically assigned IP address of 10.10.10.1 and the ability
to connect to a Dynamic Host Control Protocol (DHCP) network and receive an IP address
assignment from a DHCP server. When connecting to a DHCP network, this unit supports
Zero-Touch Provisioning, allowing the NetVanta router to download and apply configuration
parameters from a configuration management server.
R
A DHCP C
ECEIVE
1. Connect the router to an existing network that supports DHCP using the GIG 0/2
Gigabit Ethernet port on the front of the device. The NetVanta unit will automatically
request an IP address assignment from the DHCP server.
2. Check the DHCP server and record the IP address assigned to the NetVanta unit.
A
CCESS THE
Access the AOS CLI via the CONSOLE port or a Telnet or SSH session. To establish a
connection to the NetVanta unit CONSOLE port, you need the following items:
PC with VT100 terminal emulation software
Straight-through serial cable with a DB-9 (male) connector on one end and the
appropriate interface for your terminal or PC communication port on the other end.
g
NOTE
There are many terminal emulation applications available on the web. PuTTy, SecureCRT,
and HyperTerminal are a few examples.
1. Connect the DB-9 (male) connector of your serial cable to the CONSOLE port on the
back panel of the unit.
2. Connect the other end of the serial cable to the terminal or PC.
g
NOTE
Many PCs do not come with a standard serial port. A universal serial bus (USB) to serial
adapter can be used instead. The drivers for the USB to serial adapter must be installed
according to the manufacturer's instructions. If the USB to serial adapter is not properly
installed on your PC, you will not be able to communicate with the AOS unit and you should
seek support from the USB to serial adapter manufacturer.
NetVanta
NetVanta 5660
LIENT
CLI
A
DDRESS
*617005660F1-13C*
August 2019
617005660F1-13C
P/N: 17005660F1
17025660F1

Advertisement

loading

Summary of Contents for ADTRAN NetVanta 5000 Series

  • Page 1 NetVanta August 2019 617005660F1-13C P/N: 17005660F1 17025660F1 Quick Start NetVanta 5660 ETTING TARTED The NetVanta 5660 is configured using the command line interface (CLI). Entering a question mark (?) at the command prompt displays contextual help and all commands available from that prompt. This NetVanta unit ships with a statically assigned IP address of 10.10.10.1 and the ability to connect to a Dynamic Host Control Protocol (DHCP) network and receive an IP address assignment from a DHCP server.
  • Page 2 3. Provide power to the unit as appropriate. Refer to the NetVanta 4660/5660 Hardware available online at https://supportforums.adtran.com for more Installation Guide details. 4. Once the unit is powered up, open a VT100 terminal session using the following settings: 9600 baud, 8 data bits, no parity bits, 1 stop bit, and no flow control. Press ENTER to activate the AOS CLI.
  • Page 3 ELNET OGIN CCESS The following steps create a password of adtran for Telnet access. By default, Telnet access is enabled with a password of password. 1. Verify that the prompt of your unit displays (config)#. 2. Enter line telnet 0 4 to change the configuration parameters for the Telnet sessions.
  • Page 4 These guides are all available online the ADTRAN Support Community The following configuration guides provide configuration information for applications typically used within this product. All documents are available online at https://supportforums.adtran.com. NetVanta 4660/5660 Hardware Installation Guide Layer2/Layer3 Carrier Ethernet Services in AOS Configuring Port Forwarding in AOS Configuring Ethernet OAM Using Y.1731...

This manual is also suitable for:

Netvanta 566017005660f117025660f1