Makita TW202D Instruction Manual page 9

Tool with the ring spring
For impact socket without O-ring and pin
Push the impact socket onto the square drive until it
locks into place.
To remove the impact socket, simply pull it off.
► Fig.5: 1. Impact socket 2. Square drive 3. Ring
spring
For impact socket with O-ring and pin
Move the O-ring out of the groove in the impact socket
and remove the pin from the impact socket. Fit the
impact socket onto the square drive so that the hole in
the impact socket is aligned with the hole in the square
drive.
Insert the pin through the hole in the impact socket and
square drive. Then return the O-ring to the original posi-
tion in the impact socket groove to retain the pin.
To remove the impact socket, follow the installation
procedures in reverse.
► Fig.6: 1. Impact socket 2. O-ring 3. Pin
Tool with the detent pin
Align the hole in the side of the impact socket with the
detent pin on the square drive and push the impact
socket onto the square drive until it locks into place. Tap
it lightly if required.
To remove the impact socket, simply pull it off. If it is
hard to remove, depress the detent pin while pulling the
impact socket.
► Fig.7: 1. Impact socket 2. Hole 3. Square drive
4. Detent pin
Installing hook
Optional accessory
WARNING:
Use the hanging/mounting parts
for their intended purposes only, e.g., hanging the
tool on a tool belt between jobs or work intervals.
WARNING:
Be careful not to overload the
hook as too much force or irregular overburden
may cause damages to the tool resulting in per-
sonal injury.
CAUTION:
When installing the hook, always
secure it with the screw firmly. If not, the hook
may come off from the tool and result in the personal
injury.
CAUTION:
Make sure to hang the tool
securely before releasing your hold. Insufficient
or unbalanced hooking may cause falling off and you
may be injured.
The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool. To install
the hook, insert it into a groove in the tool housing on
either side and then secure it with a screw. To remove,
loosen the screw and then take it out.
► Fig.8: 1. Groove 2. Hook 3. Screw
Using hole
WARNING:
Never use the hanging hole for
unintended purpose, for instance, tethering the
tool at high location. Bearing stress in a heavily
loaded hole may cause damages to the hole, result-
ing in injuries to you or people around or below you.
Use the hanging hole at the bottom rear of the tool to
hang the tool on a wall using a hanging cord or similar
strings.
► Fig.9: 1. Hanging hole
Installing tool hanger
Optional accessory
WARNING:
Use the hanging/mounting parts
for their intended purposes only, e.g., hanging the
tool on a tool belt between jobs or work intervals.
CAUTION:
Do not use damaged tool hanger,
screws, and shoulder strap. Always check for
damages, cracks or deformations before use.
CAUTION:
Make sure that the screws are
tightened before use.
CAUTION:
Always use the screws provided
with the tool hanger only.
CAUTION:
Do not remove the battery car-
tridge while hanging the tool. The tool may fall if
the screws are not tightened.
CAUTION:
Install or remove the tool hanger
on a stable table or surface.
This tool hanger is convenient for temporarily hanging
the tool from your belt, etc. as illustrated.
► Fig.10: 1. Shoulder strap 2. Tool hanger 3. Tool
NOTE: When using with a shoulder strap, always
use the item No.161464-4. Do not use the item
No.161464-4 with other tool hanger.
Remove the battery cartridge from the tool.
Install the tool hanger to the tool in the direction of
arrow.
► Fig.11: 1. Tool hanger 2. Tool 3. Projection
► Fig.12
Insert the projections of the tool hanger into the grooves
on the both sides of the tool. You can install the tool
hanger in the direction of arrow only.
► Fig.13: 1. Projection 2. Groove
Tighten the provided screws firmly. To remove, loosen
the screws and then take it out.
► Fig.14: 1. Screw
CAUTION:
After installing, make sure that the
tool hanger is securely installed with the screws.
CAUTION:
If any problem develops, consult
your nearest Makita service center or dealer.
9 ENGLISH