Page 1
Receiver with Repeater: B127U-110-PH Este manual está disponible en español en la página de Tripp Lite: tripplite.com Ce manuel est disponible en français sur le site Web de Tripp Lite : tripplite.com Русскоязычная версия настоящего руководства представлена на веб-сайте компании Tripp Lite по адресу: tripplite.com Dieses Handbuch ist in deutscher Sprache auf der Tripp Lite-Website verfügbar:...
Product Features B127U-111-PHPH • HDMI over Cat6 Pigtail Transmitter and Receiver with Repeater Kit • Extends a 4K x 2K (3840 x 2160) @ 60 Hz A/V signal up to 230 ft. (70 m) from the source over 24 AWG Cat6 cabling •...
Page 3
Product Features B127U-002-PHPH2 • 2-Port HDMI over Cat6 Pigtail Splitter and Receivers Kit • Extends a 4K x 2K (3840 x 2160) @ 60 Hz A/V signal to two displays up to 230 ft. (70 m) from the source over 24 AWG Cat6 cabling •...
Page 4
Product Features B127U-110-PH • HDMI over Cat6 Pigtail Receiver with Repeater • Extends a 4K x 2K (3840 x 2160) @ 60 Hz A/V signal up to 230 ft. (70 m) from the source when connected to a B127U-Series transmitter or splitter unit over 24 AWG Cat6 cabling •...
Higher-gauge cabling, such as 26 AWG, has a more limited transmission capability than lower-gauge cabling. All Tripp Lite N202-Series Cat6 cables are made with 24 AWG solid wire cabling. • The installation diagram shows a B127U-111-PHPH extender kit.
Page 6
2. Connect the pigtail HDMI connector on the transmitter unit to the HDMI input on the source. Optional: Using an HDMI 2.0 cable (such as Tripp Lite’s P569-XXX-CERT or P568-XXX-2A Series cables), connect a display to the LOCAL port on the transmitter unit.
Page 7
Installation 6. Connect the pigtail USB-A connector on the remote receiver unit to a USB power adapter (5V/1A) or a USB 3.0 port on the display. The LEDs next to the RJ45 connectors will illuminate orange to indicate the ports are receiving power. Optional: The transmitter and receiver units can be charged via the Micro-USB ports on each unit by connecting a Micro- USB to USB-A cable between each unit and a USB power...
Page 8
Higher-gauge cabling, such as 26 AWG, has a more limited transmission capability than lower-gauge cabling. All Tripp Lite N202-Series Cat6 cables are made with 24 AWG solid wire cabling. • The installation diagram shows a B127U-002-PHPH2 splitter kit.
Page 9
Installation 1. Make sure all equipment in the installation – such as TVs, Blu-ray players and the transmitter – is powered off. 2. Connect the pigtail HDMI connector on the transmitter unit to the HDMI input on the source. 3. Using Cat6 cable, connect the RJ45 ports on the local transmitter unit to the RJ45 input ports of each remote receiver unit.
Page 10
Installation 8. Turn on the power to the HDMI source. The LEDs on the transmitter and receiver units should begin to flash to indicate video is being transmitted and the video should now display on the connected monitor(s). Note: If a daisy-chain installation is desired, repeat steps 4-7 with up to 3 additional B127U-110-PH or B127U-110-PD units (sold separately).
PRODUCT REGISTRATION Visit tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!* * No purchase necessary. Void where prohibited. Some restrictions apply. See...
Page 12
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice. Photos and illustrations may differ slightly from actual products.