Page 1
NOTE: Please read all instructions carefully before using this product Safety Notice POWERHOUSE HOME GYM Hardware Identifier WM 1402 Assembly Instruction Parts List Resistance Chart Warranty Ordering Parts Model WM 1402 Retain This Manual for Reference 06-27-01 IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746...
ORDERING PARTS..................BEFORE YOU BEGIN Thank you for selecting the POWERHOUSE WM 1402 HOME GYM by IMPEX FITNESS PRODUCTS. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction.
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
ASSEMBLY INSTRUCTION Tools Required to Assemble the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Rear Stabilizer (#2) to the back of the Base Frame (#1). Then attach the Rear Vertical Beam (#4) to the back of the Rear Stabilizer (#2).
Page 6
STEP 2 (See Diagram 2) A.) Attach the Front Press Base (#7) to the Base Frame (#1). Align the holes and insert through a M10 x 9 5/8” Axle (#38). Secure the Axle with two ∅ ¾” Washers (#114) and M10 Aircraft Nuts (#112).
Page 7
STEP 3 (See Diagram 3) A.) Attach the Seat Support (#12) to the Leg Developer Holder (#118). Secure it with three M10 x 5/8” Allen Bolts (#102) and ∅ ¾” Washers (#114). B.) Attach the Leg Developer Holder (#118) to the Base Frame (#1). Secure it with a M10 x 3 ¾” Carriage Bolt (#92), ∅...
Page 8
STEP 4 (See Diagram 4) A.) Slide two Rubber Bumpers (#70) onto the two Weight Plate Guide Rods (#19). Insert the two Rods into the holes on the Base Frame (#1). B.) Slide ten Weight Plates (#27) from the top of the Guide Rods (#19) down to the Bumper. Insert the Selector Rod (#16) into the center hole on the Plates.
Page 10
STEP 5 (See Diagram 5) A.) Attach the Right Butterfly (#9) to the Upper Frame (#10). Slide a ∅1 ½” Washer (#51) and ∅1 3/8” Steel Cap (#84) onto the axle. Secure the Cap with a M6 x 1 ½” Hex Bolt (#106) and M6 Aircraft Nut (#113).
Page 12
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Insert the 110” Upper Cable (#30) through the opening at the front of the Upper Frame (#10). NOTE: The Ball Stopper on the Cable should be underneath the Frame. Attach a Big Pulley (#79) to the opening and secure it with one M10 x 3 ½”...
Page 13
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach a Pulley (#79) to the bracket on the Right Butterfly (#9). Secure it with a M10 x 1 ¾” (#99), two ∅ ¾” Washers (#114), and one M10 Aircraft Nut (#112). B.) Repeat the step (A) above to install another Pulley to the Left Butterfly.
Page 14
STEP 8 (See Diagram 8 & Cable Loop Diagram) A.) Insert the 159” Lower Cable (#31) through the opening on the bottom of the Leg Developer (#13). NOTE: The Ball Stopper on the Cable should be in front of the Leg Developer. Attach a Pulley (#79) to the opening and secure it with one M10 x 2 ½”...
Page 15
STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach the136” Bench Press Cable (#34) to the open slot on Pulley Cable Hanger (#45) previously installed in Step 8. B.) Pull the Cable downward to the open bracket on top of the Base Frame (#1). Install a Pulley (#79).
Page 16
STEP 10 (See Diagram 10 & Cable Loop Diagram) A.) Plug one ∅1/2” Plastic Bushing (#76) into the hole on the side of the Rear Vertical Beam (#4) from the bottom up. Insert the “long bolt end” of the 72 ½” Power Booster Cable (#33) into the hole.
Page 17
STEP 11 (See Diagram 11) A.) Attach the Seat (#28) to the Seat Support (#12). Secure it with two M8 x 2 ½” Allen Bolts (#103) and ∅ 5/8” Washers (#115). B.) Attach the Backrest Pad (#29) to the Front vertical Beam (#3). Secure it with two M8 x 2” Allen Bolts (#104) and ∅...
HOW TO USE How to use the quick release connector. The Clip is removed from the Connector. Connector Clip Place the chain in between the connector and insert the Clip through the holes. Chain Insert Push down the Clip to secure.
∅ ¾” Washer 5 5/8” x 1 ½” Bracket ∅ 5/8” Washer 4 5/8” x 3” Bracket M10 x 7 7/8” Rod 1 ½” x 3” Impex Logo End Cap ∅ 1” Washer Lat Bar Grip Leg Developer Holder Grip ∅...
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the customer. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for commercial or rental purposes.