Operation - DeWalt XR DWH161 Manual

• DO NOT overheat the coin cell or throw it into fire.
The coin cell may leak, explode, catch fire and cause
personal injury.
DO NOT damage the coin cell and do not disassemble
•
the coin cell. The coin cell may leak, explode, catch fire and
cause personal injury.
• DO NOT allow damaged coin cells to come into
contact with water. Leaking lithium may mix with water
to create hydrogen, which could cause a fire, an explosion, or
personal injury.
• DO NOT dispose of the button cell battery with normal
household waste. Contact your local waste disposal
department to dispose of the device/batteries in accordance
with applicable local laws and regulations.
• Remove and dispose of drained coin cell correctly.
Drained coin cell may leak and damage the product or cause
personal injury.
1. To open the housing remove the 4 screws
panel with a T10 torx screwdriver.
2. Pull out sideways the discharged coin cell battery fom the
battery holder.
3. Insert sideways the new coin cell battery
holder, and pay attention to the orientation of the battery in
terms of polarity.
4. Replace the back cover, insert the screws and tighten.

OPERATION

Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn the dust extractor off and disconnect
battery pack before making any adjustments or
removing/installing attachments or accessories. An
accidental start-up can cause injury.
Proper Hand Position (Fig. D, F)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
If used as a stand‑alone dust extractor, proper hand position
requires one hand on the accessory.
Using the Dust Extractor (Fig. A, E, L)
• Before using the universal dust extractor, ensure that the
filter is in place and filter box is securely fitted.
• Do not use damaged filters. Replace any damaged
filters immediately.
• Please observe national applicable regulations/laws on how
to handle harmful types of dust in your country.
1. Attach the appropriate accessory to the dust extractor hose
2. Insert the battery pack
21 from the rear
into the battery
22
1 .
3. To turn dust extractor on, press the three position switch
to the On (I) position or press the button
connected remote. Each click will let the dust extractor
change the status between on and off.
4. To use in Wireless Tool Control™ mode press the three
position switch to the Wireless Tool Control™ ( ) position.
Once paired the trigger of the connected tool or the
button 24 of the remote will control the dust extractor.
nOTE: Refer to Pairing the Dust Extractor with a Tool
using Wireless Tool Control™ Mode to use the dust
extractor with a Wireless Tool Control™ equipped tool.
5. When finished, turn the dust extractor off by pressing the
three position switch to the Off (O) position or releasing the
trigger of the Wireless Tool Control™ equipped tool. Pressing
the button 24 once on the connected remote can also turn
off the dust extractor.
Pairing the Dust Extractor with a Tool Using
Wireless Tool Control™ Mode (Fig. A, H, L)

CAUTION: When the dust extractor is being controlled
by a paired power tool or remote it may start or stop
without warning.
To Pair with a D
Control™ Tool
1. Press the three position switch
Control™ ( ) position.
2. Press and hold the Wireless Tool Control™ pairing button
on the DWH161 and pull the trigger on the Wireless
Tool Control™ equipped tool or press the button
the remote (Fig. L, item
same time.
3. The LED will be steadily illuminated to indicate a
9
successful pairing.
nOTE: Only one transmitter can be paired to the DWH161
at a time. If the unit is already paired the previous
transmitter will be overridden.
To Unpair with a Wireless Tool control™ Tool
• Press and hold the Wireless Tool Control™ pairing button
on the DWH161 and pull the trigger on the Wireless Tool
Control™ equipped tool or press the button on the remote
(Fig. L, item 23
• The LED will flash slowly to indicate a successful unpairing.
9
LED FLASH PATTERN
In pairing mode
No device is paired
Device is successfully paired
Filter Cleaning Mechanism
Suction power is dependent on the condition of the filter.
Therefore, the filter should be cleaned regularly.
The filter cleaning mechanism is a feature that uses the motor
.
6
in the dust extractor to force air through the filter. Refer
to Emptying the Dust Collection Box for instructions on
proper use.
24
WALT Remote or Wireless Tool
e
7 to the Wireless Tool
23 *optional accessory) at the
*optional accessory) at the same time.
– – – – – – –
– – – – – – – –
– – – –
EnGLIsh
7
once on the
8
24 on
8
35