Maintenance - DeWalt XR DWH161 Manual

EnGLIsh
Emptying the Dust Collection Box (Fig. I, J)

WARNING: The vacuum cleaner contains dust particles
that pose a risk to health. Emptying and maintenance
procedures, including the disposal of dust collectors,
should only be carried out by professionals. Suitable
protective equipment is required. Do not operate the
vacuum cleaner without the complete filter system.
Otherwise you endanger your health.

WARNING: Wear approved eye protection and approved
dust mask when performing this procedure.

CAUTION: Do not clean with water or compressed air.
The dust collection box 3 should be emptied as soon as the
performance has noticeably decreased or is full.
1. Press the dust collection box release buttons
dust collection box away from the dust extraction system.
Once the catch mechanism is clear of the dust extraction
system the upper joint will also release allowing the dust
collection box to be removed completely.
2. To empty the dust collection box
suitable container to catch the dust contained within it.
Lift up the assembly release latch
collection box, separating the canister from the lid. Gently
tapping the dust collection box will encourage any dust
trapped within the filter to also be removed. Once the filter
lid and canister are empty reattach them, ensuring the
assembly release latch
Figure J.
3. To reattach the dust collection box to the dust extraction
system first insert the rounded profile of the upper joint
into the recess on the dust extraction system. Pivot the dust
collection box down so that the release buttons click back
into place. Refer to Figure I.
4. With the dust collection box properly installed, depress the
filter cleaning mechanism
Allow the system to run for 5 seconds and release trigger.
This should be done after every emptying of the dust
collection box.
Transporting the Dust Extractor

WARNING: Accidental start-up during transport could
be hazardous. Always transport the dust extractor
with the batteries removed. Refer to the Battery
Packs, Transportation section of this manual for
further information.

WARNING: Check the tool and batteries for damage after
transport and before use.
Storing the Dust Extractor

WARNING:
a ) Empty the dust collection box before storing the
dust extractor.
b ) Always store your dust extractor with the batteries removed!
c ) Store the tool and batteries in a place that is as cool and
dry as possible.
36
4 and pull the
3 position it over a
to open the dust
18
18 is securely fastened. Refer to
5 and turn on the dust extractor.
d ) Store the tool and batteries in a place that cannot be
accessed by children or unauthorised persons.
e ) Check the tool and batteries for damage after long periods
of storage.
f ) Refer to the Battery Packs, Transportation section of
this manual for further information.

MAINTENANCE


WARNING: To reduce the risk of serious personal
injury, turn the dust extractor off and disconnect
battery pack before making any adjustments or
removing/installing attachments or accessories. An
accidental start-up can cause injury.
The charger and battery pack are not serviceable.
nOTE: Cleaning and user maintenance shall not be made
by children.
Replacing the Dust Collection Box Filter
Assembly (Fig. I, J)

WARNING: Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Replace any damaged filters immediately.
nOTE: The filter should be replaced after every 350 full to empty
filter box emptying cycles.
1. Press the dust collection box release buttons
dust collection box away from the dust extraction system.
Once the catch mechanism is clear of the dust extraction
system the upper joint will also release allowing the dust
collection box to be removed completely.
2. Discard dust collection box
filter box.
3. Reattach the dust collection box to the dust extraction
system. First insert the rounded profile of the upper joint
into the recess on the dust extraction system. Pivot the dust
collection box down so that the release buttons click back
into place.
Lubrication
Your dust extractor requires no additional lubrication.
Cleaning

WARNING: Do not use a spray system, pressure jet washer
or running water for cleaning.

WARNING: Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Do not use a brush or compressed air to clean
the dust collector or filter.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the dust extractor.
These chemicals may weaken the materials used in these
parts. Use a cloth dampened only with water and mild
soap. Never let any liquid get inside the dust extractor;
never immerse any part of the dust extractor into a liquid.
During intensive use the dust collector becomes clogged
with dust. Refer to Replacing The Dust Collection Box Filter
Assembly, under Maintenance.
4 and pull the
and replace with a new
3