Table of Contents
Advertisement
58SC0B/58SC1B: Installation, Start–Up, Operating and Service and Maintenance Instructions
f. Press Next/Option button to cycle through the fault history.
Faults remain in memory for 72 hours of powered operation after
the last fault occurs. Faults may be manually cleared by selecting
(CLr) with the menu/select button.
CARE AND MAINTENANCE
WARNING
!
FIRE OR EXPLOSION HAZARD
Failure to follow this warning could result in personal injury, death
and/or property damage.
Never store anything on, near, or in contact with the furnace, such as:
1.
Spray or aerosol cans, rags, brooms, dust mops, vacuum
cleaners, or other cleaning tools.
2.
Soap powders, bleaches, waxes or other cleaning compounds,
plastic or plastic containers, gasoline, kerosene, cigarette lighter
fluid, dry cleaning fluids, or other volatile fluids.
3.
Paint thinners and other painting compounds, paper bags, or
other paper products.
For continuing high performance and to minimize possible equipment
failure, periodic maintenance must be performed on this equipment.
Consult your local dealer about proper frequency of maintenance and the
availability of a maintenance contract.
WARNING
!
ELECTRICAL SHOCK AND FIRE HAZARD
Failure to follow this warning could result in personal injury, death or
property damage.
Turn off the gas and electrical supplies to the unit and install lockout tag
before performing any maintenance or service. Follow the operating
instructions on the label attached to the furnace.
WARNING
!
CARBON MONOXIDE POISONING AND FIRE
HAZARD
Failure to follow this warning could result in personal injury, death
and/or property damage.
Never operate unit without a filter or with filter access door removed.
CAUTION
!
CUT HAZARD
Failure to follow this caution may result in personal injury.
Sheet metal parts may have sharp edges or burrs. Use care and wear
appropriate protective clothing, safety glasses and gloves when
handling parts and servicing furnaces.
The minimum maintenance on this furnace is as follows:
1. Check and clean/replace air filter each month or more frequently if
required. Replace if torn.
2. Check blower motor and wheel for cleanliness each heating and
cooling season. Clean as necessary.
3. Check electrical connections for tightness and controls for proper
operation each heating season. Service as necessary.
4. Inspect burner compartment before each heating season for rust,
corrosion, soot or excessive dust. If necessary, have furnace and
burner serviced by a qualified service agency.
Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.
5. Inspect the vent pipe/vent system before each heating season for
rust, corrosion, water leakage, sagging pipes or broken fittings.
Have vent pipes/vent system serviced by a qualified service agency.
6. Inspect any accessories attached to the furnace such as a humidifier
or electronic air cleaner. Perform any service or maintenance to the
accessories as recommended in the accessory instructions.
Cleaning and/or Replacing Air Filter
The air filter arrangement will vary depending on the application. The
filter is exterior to the furnace casing.
NOTE: If the filter has an airflow direction arrow, the arrow must point
towards the blower.
To clean or replace filters, proceed as follows:
!
ELECTRICAL SHOCK, FIRE OR EXPLOSION HAZARD
Failure to follow this warning could result in personal injury or death,
or property damage.
Before installing, modifying, or servicing system, main electrical
disconnect switch must be in the OFF position and install a lockout tag.
There may be more than one disconnect switch. Lock out and tag
switch with a suitable warning label. Verify proper operation after
servicing. Always reinstall access doors after completing service and
maintenance.
1. Turn off electrical supply to furnace before removing filter access
door.
2. Remove filter cabinet door.
3. Slide filter out of cabinet.
4. If equipped with permanent, washable 3/4-in. (19 mm) filter, clean
filter by spraying cold tap water through filter in opposite direction
of airflow. Rinse filter and let dry. Oiling or coating of the filter is
not recommended. See
5. If equipped with factory-specified disposable media filter, replace
only with media filter having the same part number and size. For
expandable replacement media, refer to the instructions included
with the replacement media.
6. Slide filter into cabinet.
7. Replace filter cabinet door.
8. Turn on electrical supply to furnace.
Table 18 – Filter Size Information (In. / mm)
FURNACE
FILTER SIZE (In. / mm)
CASING
WIDTH
Side Return
In. (mm)
14-1/2
16 x 25 x 3/4
(368)
(406 x 635 x 19)
17-1/2
16 X 25 X 3/4
(445)
(406 x 635 x 19)
21
16 x 25 x 3/4
(533)
(406 x 635 x 19)
24
16 x 25 x 3/4
(610)
(406 x 635 x 19)
*. Recommended
37
WARNING
Table 18
for size information.
Bottom Return
14 x 25 x 3/4
(356 x 635 x 19)
16 X 25 X 3/4
(406 x 635 x 19)
20 X 25 X 3/4
(508 x 635 x 19)
24 X 25 X 3/4
(610 x 635 x 19)
FILTER
*
TYPE
Washable
Washable
Washable
Washable
Advertisement
Table of Contents
