Ice storage bins ice machine with ride technology (16 pages)
Summary of Contents for Follett HME1000ABT
Page 1
™ Horizon Ice Machine Installation Instructions to Ice Storage Bin Top-mount Applications HCC/HMC/HCE/HME1000ABT, HCC/HMC/HCE/HME1400ABT, HCC/HMC/HCE/HME1000WBT, HCC/HMC/HCE/HME1400WBT, (See model number confi gurator on page 2 for details.) Order parts online self-contained www.follettice.com Stock Module Identification Plate 208264 Module No. Product Service No.
Page 2
Chewblet ® Ice Machine Model Number Configurations 1400 Icemaker Voltage Series Condenser Application Configuration MC Maestro™ C 208-230/60/1 (icemaking head) 400 up to A Air-cooled, self-contained V Vision™ S RIDE™ Self-contained only. 454 lbs Chewblet ® W Water-cooled, self-contained H Harmony™ (RIDE remote D 115/60/1 (icemaking head) (206kg)
Page 3
Read and complete the following 8 installation steps Unpack Site preparation Bin preparation Louvered docking assembly External connection Ice transport tube Internal connection Front cover BIN • TOP-MOUNT self-contained...
Page 4
Unpack Carefully unpack and inspect the contents of your Follett ice machine. Unpack ice machine ➊ ➋ ➌ ➍ 1/2" 1/2" ➎ ➏ BIN • TOP-MOUNT self-contained...
Potable water supply • 10-70 psi (69-483kpa) • 45 to 90 F (7 to 32 C) • Follett recommends the use of an in-line water fi ltration system (#00130286) ➌ Condenser water supply for water-cooled systems • 10 psi min.; 150 psi max. (69kpa min.; 1034kpa max.) •...
Page 6
Bin preparation Prepare the bin. Bin top preparation Bin top preparation ➋ ➊ ➌ ➊ ➊ • Remove protective tape from gaskets • Apply gaskets ➋ • Install shuttle actuator through dispenser top and secure with locking nut ➌ BIN • TOP-MOUNT self-contained...
Page 7
Louvered docking assembly Install the louvered docking assembly. WARNING • Docking station must be secured in accordance with these instructions to ensure ice machine stability. • Ventilation openings in the louvered docking station should be clear of obstruction Louvered docking assembly •...
Ice transport tube Install the ice transport tube. Ice transport tube installation Hot Water 160 F (71 C) • Install supplied ice transport tube insulation ➊ • Heat end of transport tube in cup of 160 F (71 C) hot water to soften and spread with pliers before making connection to ease assembly ➋...
Internal connections Connect louvered docking assembly to ice machine. CAUTION • Plug must be accessible after fi nal installation. • H_E1400A/W 230/50/1 requires a 20A circuit (4.00 mm wire) Air-cooled ice machines – follow steps 7.1 through 7.4. Ice transport tube Potable water line ➊...
Page 11
Water-cooled ice machines – follow steps 7.5 through 7.10. Cooling lines Ice transport tube ➋ ➊ • Install ice machine cooling water lines to • Slide ice machine into louvered docking ➊ louvered docking assembly assembly • Insert ice transport tube into coupling and ➋...
Page 12
7.10 Power cord Power cord • Remove twist tie • Position plate into opening and secure with supplied screw • Carefully pass plug thru opening and plug into wall outlet BIN • TOP-MOUNT self-contained...
Front cover Install front cover to ice machine. Water-cooled ice machines only ➋ ➊ • Slide ice machine cover over machine ensuring that tabs on back of cover slip under louvers on back of louvered ➊ docking assembly • Insert and tighten two screws through cover and into louvered docking assembly ➋...
Page 14
Long tube run recommendations max. 2 ft (0,6m) 1/4" (6,4mm) 1' (0,3m) ➊ • Pitch ice transport tube to allow melt water to drain towards ice machine ➋ • Secure insulated ice transport tube at least every 2 ft (0,6m) to prevent dips or traps BIN •...