Table of Contents
Advertisement
44
GETTING TO KNOW YOUR VEHICLE
CAUTION!
Do not use abrasive cleaning components, solvents,
steel wool or other abrasive materials to clean the
lenses.
D
R
L
AYTIME
UNNING
IGHTS
The Daytime Running Lights (DRLs) come on whenever the
engine is running. The lights will remain on until the
ignition is placed in the OFF position, or the parking brake
is engaged. The headlight switch must be used during
normal nighttime driving.
NOTE:
For vehicles sold in Canada, the Daytime Running
Lights will automatically deactivate when the front fog
lights are turned on.
If allowed by law in the country in which the vehicle was
purchased, the Daytime Running Lights can be turned
on and off using the Uconnect system
On some vehicles, the Daytime Running Lights may
deactivate or reduce intensity on one side of the
vehicle (when a turn signal is activated on that side), or
on both sides of the vehicle (when the hazard warning
lights are activated).
H
/L
IGH
OW
Push the multifunction lever toward the instrument panel
to switch the headlights to high beams. Pulling the
multifunction back will turn the low beams on.
A
UTOMATIC
(DRL
)
S
The Automatic High Beam Headlamp Control system
provides increased forward lighting at night by
automatically controlling the high beams through the use
of a camera mounted on the inside rearview mirror. This
camera detects vehicle specific light and automatically
switches from high beams to low beams until the
approaching vehicle is out of view.
NOTE:
The Automatic High Beam Headlamp Control can be
turned on or off by selecting or deselecting "Auto Dim
High Beams" within your Uconnect Settings
page 135, as well as turning the headlight switch to
Ú
the AUTO position.
page 135.
Ú
Broken, muddy, or obstructed headlights and taillights
of vehicles in the field of view will cause headlights to
remain on longer (closer to the vehicle). Also, dirt, film,
and other obstructions on the windshield or camera
lens will cause the system to function improperly.
If the windshield or Automatic High Beam Headlamp
Control mirror is replaced, the mirror must be re-aimed
to ensure proper performance. See a local authorized
dealer.
To opt out of the Advanced Auto High-Beam Sensitivity
Control (default) and enter Reduced High-Beam Sensi-
tivity Control (not recommended), toggle high beam
B
S
EAM
WITCH
H
B
— I
E
IGH
EAM
F
QUIPPED
lever six full on/off cycles within 10 seconds of ignition
ON. System will return to default setting upon ignition
off.
F
-T
-P
LASH
O
ASS
You can signal another vehicle with your headlights by
lightly pulling the multifunction lever toward you. This will
cause the high beam headlights to turn on, and remain on,
until the lever is released.
A
H
UTOMATIC
EADLIGHTS
This system automatically turns the headlights on or off
according to ambient light levels. To turn the system on,
rotate the headlight switch counterclockwise to the AUTO
position. When the system is on, the headlight time delay
feature is also on. This means the headlights will stay on
for up to 90 seconds after you place the ignition into the
OFF position. The headlight time delay can be
programmed 0/30/60/90 seconds within Uconnect
Settings
page 135.
Ú
To turn the automatic system off, move the headlight
switch out of the AUTO position.
NOTE:
The engine must be running before the headlights will
come on in the automatic mode.
P
L
A
P
ARKING
IGHTS
ND
ANEL
To turn on the parking lights and instrument panel lights,
rotate the headlight switch clockwise. To turn off the
parking lights, rotate the headlight switch back to the O
(off) position.
L
IGHTS
Advertisement
Table of Contents
