Stiga MCS 470 Li D48 Series Operator's Manual page 39

/ disables the machine electric circuit (Fig. 4).
Removing the key, the electric circuit is completely deactivated
to prevent uncontrolled use of the machine.
IMPORTANT Remove the safety key whenever the machine
is unused or left unattended.
• Operator presence lever
The operator presence lever (Fig. 5.A) enables the
engagement of the cutting device. The handle is located in
the front position.
Press the safety button (Fig. 5.C) and move the lever towards
the handle to start the cutting device.
When the lever is released, the motor automatically stops
and all functions are disabled.
• Power button (if provided)
The power button (Fig. 6.A) is used for:
Switching on the machine.
Pressing the button (Fig. 6.A) the LED (Fig. 6.B) turns
on and the machine is ready for use.
NOTE The machine can only be switched on if the
operator presence lever and the drive lever are released.
NOTE If the machine is not used, the LED turns off
after 15 seconds and the above-mentioned operation
must be carried out again.
Cutting means engagement.
NOTE The cutting device engagement is possible on-
ly by pressing the operator presence lever against the
handle (see par. 6.3).
Cutting means disengagement.
With the cutting device engaged, release the operator
presence lever (Fig. 5.A); the cutting device stops
keeping the machine switched on.
• Drive lever (if provided):
This engages the wheel drive and allows the machine
to move forward (Fig. 6.B). The handle is located in
the rear position.
IMPORTANT The engine must always be running with the
drive disengaged.
IMPORTANT To prevent damage to the transmission, do not
pull the machine backwards with the drive engaged.
For some models it's possible to adjust the feed speed using
the selection knob on the right of the handle (Fig. 6.C).
You can select 6 different levels of speed.
Maximum speed (about 5 Km/h).
Minimum speed (about 2.5 Km / h)
NOTE The last speed level selected remains set also after the
machine shutdown.
• "ECO" button (if provided)
The "ECO" mode allows to save energy when cutting the grass,
optimising the battery life. To activate or deactivate the "Eco"
function, press the button (Fig. 6.D).
This mode automatically turns off when the operator presence
lever is released.
NOTE It is not recommended to use the "ECO" function in
heavy grass cutting conditions (cutting of dense, high, humid
grass).
• Cutting height adjustment
By lowering or raising the chassis the grass can be cut at
different heights. (Fig. 7)
IMPORTANT This operation must be carried out when the
cutting device is stationary.
5. USING THE MACHINE
IMPORTANT For instructions regarding the engine and the
battery (if supplied), read the relevant manual.
5.1. PRELIMINARY PROCEDURES
Place the machine in a stable horizontal position on the ground.
• Checking the battery
Before using the machine for the first time after purchase,
fully charge the battery following the instructions in the
battery booklet.
Before every use of the machine, check the battery charge
status according to the instructions in the battery booklet.
5.2. SAFETY CHECKS
• Check the integrity and correct assembly of all machine
components;
• Make sure that all fasteners are tightened correctly;
• Keep every surface of the machine clean and dry.
Action
1. Start the machine.
2. Release the switch control.
1. Start the machine.
2. Engage the drive lever.
3. Disengage the drive lever.
1. Test drive.
If any of the results fail to match the indications
provided in the tables, do not use the machine!
Contact a service centre to have it checked and
repaired if necessary.
5.3. START-UP AND WORK
NOTE Start the machine on a level surface free from obsta-
cles or grass.
Start the machine as shown in (Fig. 8).
IMPORTANT Always maintain a safe distance from the cut-
ting device while working, corresponding to the length of the
EN - 4
Result
1. The cutting means should
move.
2. The levers must return to the
neutral position automatically
and quickly, the engine must
switch off and the cutting
device must stop within a few
seconds.
2. The machine moves forward.
3. The machine comes to a
standstill.
1. No abnormal vibrations.
No abnormal sound.