Table of Contents
Advertisement
Available languages
Available languages
Installation
5
5.2.2 Outside back exhaust
(horizontal duct type B)
3/8" TO EDGE
12"
TO
NOTE: IT IS VERY IMPORTANT
READ AND FOLLOW
THE DIRECTIONS
INSTRUCTION S
IN THE INSTALLATION
WITH THIS
BEFORE PROCEEDING
REAR WALL TEMPLATE.
4"
This Rear Wall Template
serves to position the bottom
the horizontal exhaust
mounting plate and to locate
outlet.
1. Use a level to check that
the template is positioned
accurately.
one stud on the left or
2. Locate and mark at least
right side of the centerline.
It is important to use at
least one wood
a stud to support the weight
screw mounted firmly in
two additional, evenly spaced
of the microwave. Mark
locations for the supplied
toggle bolts.
locations. Where there is
3. Drill holes in the marked
for wood screws. For holes
a stud, drill a 3/16" hole
that do not line up with a
stud, drill 5/8" holes for
toggle bolts.
MOUNTING PLATE
DO NOT INSTALL THE
AT THIS TIME.
from the rear wall.
4. Remove the template
book for your
5. Revie
w
h t
e Installation Instruction
installation situation.
para consultar la
Darle vuelta a la hoja
versión en Español.
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
STUD ON EITHER SIDE
OF
LOCATE AT LEAST ONE
THE CENTERLINE.
EVENLY
MARK THE LOCATION
FOR 2 ADDITIONAL,
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
along the dotted line.
Trim the rear wall template
Installation overview
B1. Prepare Rear Wall
B2. Remove Blower Plate
B3. Attach Mounting Plate to Wall
B4. Prepare Top Cabinet
B5. Adjust Blower
B6. Mount the Microwave Oven
Make sure the screws for the blower
A
motor and blower plate are securely
tightened when they are reinstalled.
This will help to prevent excessive
vibration.
A
Make sure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
Over The Range Convection Microwave Oven / Installation Manual
along the dotted line.
Trim the rear wall template
to align with holes in the
Locate and mark holes
t a
. e
m
o
u
t n
n i
g
l p
IMPORTANT:
STUD ON EITHER SIDE
OF
LOCATE AT LEAST ONE
THE CENTERLINE.
EVENLY
MARK THE LOCATION
FOR 2 ADDITIONAL,
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
B1. Preparing the rear wall for out-
side back exhaust
You need to cut an opening in the rear wall for out-
side exhaust.
NOT E:
REA D
IT IS VER
AND FOLL
Y IMPO
IN THE
OW THE
RTAN
T TO
BEFO
INST AL
DIRE CTIO
RE PRO
L
A
T
I
O
N
REA R
CEE DING
I
N
S
TRU CTIO
NS
WAL L
TEM PLAT
WITH
NS
This Rear
THIS
3/8" TO EDGE
mount ing
Wall Templ
E.
outlet.
plate and
ate serves
to positio
12"
1. Use
to locate
the horizon
n the bottom
a level
tal exhaus
accura
tely.
to check
that the
t
2. Locate
templa
right side
and mark
te is positio
ned
of the center
at least
one stud
4"
It is import
line.
on the
left or
screw mount
ant to use
of the microw
ed firmly
at least
locatio ns
ave. Mark
in a stud
to suppor
one wood
3. Drill
for the
two additio
t the weight
holes in
supplie
d toggle
nal, evenly
a stud,
drill a 3/16"
the marke
bolts.
spaced
that do
hole for
d locatio
ns. Where
toggle
not line
up with
wood screws
there is
bolts.
a stud,
. For holes
DO NOT
drill 5/8"
holes for
AT THIS
INSTA LL
4. Remov
TIME.
THE MOUN
5. Review
e the templa
TING PLATE
the Installa
te from
the rear
installa
tion situatio
tion Instruc
wall.
n.
tion book
for your
Darle vuelta
versió n
a la hoja
en Españ
para consu
ol.
ltar la
Loca te
and mark
moun ting
holes to
IMPO RTAN
plate .
align with
holes in
LOC ATE
T:
the
AT LEAS
THE CEN
T ONE
TERL INE.
STUD
MAR K
ON EITH
THE LOC
ER SIDE
SPAC
ED TOG
ATIO N
OF
GLE BOLT
FOR 2
ADD ITION
ARE A.
S IN THE
AL, EVEN
MOU NTIN
LY
G PLAT
E
Trim the
rear wall
temp late
alon g
the dotte
d line.
Loca te
and mark
moun ting
IMPO RTAN
LOC ATE
THE CEN
MAR K
THE LOC
SPA CED
ARE A.
• Read the instructions on the REAR WALL
TEMPLATE.
• Tape it to the rear wall, lining up with the holes
previously drilled for holes A and B in the wall
plate.
• Cut the opening, following the instructions of
the REAR WALL TEMPLATE.
Trim the
rear wall
temp late
alon g
the dotte
d line.
holes to
plate .
align with
holes in
T:
the
AT LEAS
T ONE
TERL INE.
STUD
ON EITH
ER SIDE
ATIO N
TOG GLE
FOR 2
OF
BOLT S
ADD ITION
IN THE
AL, EVEN
MOU NTIN
LY
G PLAT
E
23 / 63 EN
Advertisement
Chapters
Table of Contents
