Table of Contents
Advertisement
Available languages
Available languages
Installation
5
5.1 Placement of the
mounting plate
5.1.1 Removing the microwave
oven from the carton/ removing
the mounting plate
1. Remove the installation instructions, filters,
glass tray and the small hardware bag. Do not
remove the Styrofoam protecting the front of
the oven.
2. Fold back all 4 carton flaps fully against carton
sides. Then carefully roll the oven and carton
over onto the top side. The oven should be
resting in the Styrofoam.
Styrofoam
3. Pull the carton up and off the oven.
4. Cut the middle of the outer protective plastic
bag to remove the mounting plate
Screws
Mounting Plate
14 / 63 EN
Carton
Screws
Over The Range Convection Microwave Oven / Installation Manual
5. Remove the screws from the mounting plate.
This plate will be used as the rear wall template
and for mounting. Reinstall the screws into the
holes where they were removed.
5.1.2 Finding the wall studs
1. Find the studs, using one of the following
methods:
• Stud finder – a magnetic device which locates
nails.
• Use a hammer to tap lightly across the mounting
surface to find a solid sound. This will indicate a
stud location.
2. After locating the stud(s), find the center by
probing the wall with a small nail to find the
edges of the stud. Then place a mark halfway
between the edges. The center of any adjacent
studs should be 16
from this mark.
3. Draw a line down the center of the studs.
A
WARNING: The microwave must
be connected to at least one wall
stud.
5.1.3 Determining wall plate
location under your cabinet
Plate position—beneath at bottom
cabinet
NOTE:
READ
IT IS VERY
IN THE
AND FOLLO
IMPOR
TANT
BEFOR
INSTAL
W THE
DIREC
TO
REAR
E PROCE
LATION
INSTRU
TIONS
WALL
TEMPL
EDING
WITH THIS
CTION
S
This Rear
Wall Template
ATE.
3/8" TO EDGE
mounting
plate and
serves
12"
outlet.
1. Use
to locate
the horizontal
to position
the bottom
accurately
a level
to check
exhaust
2. Locate
.
that the
template
right side
and mark
at least
is positioned
4"
It is important
of the centerline
one stud
.
on the left
screw mounted
to use at
or
of the microwav
locations
e. Mark
firmly in
a stud to
least one
wood
3. Drill holes
for the supplied
two additional
support
the weight
Trim the
a stud,
in the marked
toggle bolts.
, evenly
spaced
that do
not line
drill a 3/16"
hole for
locations.
Where
toggle bolts.
up with
a stud,
wood screws.
there is
For holes
DO NOT
drill 5/8"
holes for
AT THIS
TIME.
INSTALL
THE MOUNTIN
5. Review
4. Remove
the template
G PLATE
installatio
the Installatio
from the
rear wall.
n situation.
n Instruction
book for
your
Darle vuelta
versión
a la hoja
para consulta
en Español.
r la
Locate
mountin
and mark
holes to
g plate.
align with
IMPOR
TANT:
holes in
the
LOCAT
E AT LEAST
THE CENTE
ONE STUD
MARK
RLINE.
ON EITHER
THE LOCAT
SIDE OF
SPACE
D TOGGL
ION FOR
AREA.
E BOLTS
2 ADDITI
ONAL,
IN THE
MOUNT
EVENL
Y
ING PLATE
Trim the
rear wall
templa
te along
the dotted
line.
Locate
and mark
mountin
g plate.
holes to
align with
IMPOR
TANT:
LOCAT
THE CENTE
E AT LEAST
RLINE.
ONE STUD
MARK
THE LOCAT
SPACE
D TOGGL
ION FOR
AREA.
E BOLTS
2 ADDITI
IN THE
C L
Draw a vertical line on the wall at the center of the
30 ʺ wide space. Tape the Rear Wall Template
onto the wall matching the centerline and touching
the bottom of the cabinet.
(40.6 cm) or 24
(61 cm)
"
"
rear wall
templa
te along
the dotted
line.
16-1/2
holes in
the
ON EITHER
SIDE OF
ONAL,
MOUNT
EVENL
Y
ING PLATE
Advertisement
Chapters
Table of Contents
