Panasonic HC-X2000 Owner's Manual page 190

Message
Screen display
Camera image screen
[CANNOT PLAY.]
[CANNOT DELETE.]
[CANNOT RECORD. THE NUMBER
OF CLIPS HAS EXCEEDED THE
MAXIMUM LIMIT.]
[CARD ERROR. PLEASE
REFORMAT.]
[CANNOT COPY TO SAME CARD.]
[Repair failed.]
[UNABLE TO FORMAT.]
[CANNOT PROTECT.]
[THE CLIP IS PROTECTED. PLEASE
CANCEL PROTECTION.]
[THUMBNAIL DATA ERROR IS
DETECTED.]
[CANNOT RECORD -
INCOMPATIBLE CONTROL DATA.]
[CANNOT SET.]
[THIS CLIP CANNOT BE COPIED.]
[CONTROL DATA ERROR HAS
BEEN DETECTED. (SD CARD)]
[COPY FAILED. PLEASE CHECK
THE CARD.]
[CANNOT COPY - THE NUMBER OF
CLIPS HAS REACHED MAXIMUM.]
[LOW BATTERY. PLEASE CONNECT
AC ADAPTOR OR CHANGE
BATTERY.]
[CANNOT PLAY THIS CLIP ON THIS
MODEL.]
[Cannot copy: contains recordings
from other devices.]
[INVALID]
[Cannot record - Playlist capacity is
full.]
[Cannot copy - Playlist capacity is full.] The unit tried to copy to a memory card where the number
[Exceeds capacity. Please reselect.]
[Check the destination media.]
[LOAD NG]
[SAVE NG]
[DISCONNECT USB CABLE.]
[CARD LOCKED.]
[CANNOT SELECT MORE CLIPS.]
[SELECT THE CLIP TO BE
DELETED.]
[SELECT THE CLIPS TO COPY.]
Chapter 10 Notes — Warning system
Description
This is a clip that cannot be played back.
(When it cannot be played back due to difference of the
system frequency, etc.)
An error has occurred during playback, and the playback
has stopped.
This is a clip that cannot be deleted.
The number of clips that can be recorded has reached the
maximum.
Formatting of the memory card has failed.
The clip recorded over multiple memory cards cannot be
copied to a same card.
Repairing the clip where an error occurred has failed
because the power was disconnected or the memory card
was removed during recording.
Restoring of the management information has failed.
This memory card cannot be formatted.
This is a clip that cannot be protected.
The clip is protected so it cannot be deleted.
An error occurred in the thumbnail information of the
memory card.
The version of the management information on the
memory card is not supported.
This cannot be set.
The clip cannot be copied.
An error occurred in the management information of the
memory card.
The clip has failed to copy due to an error in the memory
card.
The number of clips that can be copied has reached the
maximum.
It is trying to copy a clip or update the firmware of the unit
when the remaining battery level is insufficient.
This is a clip that cannot be played back with the unit.
The clip recorded in other device cannot be copied.
Operation is disabled.
The unit tried to record on a memory card where the
number of playlists for recording has reached the
maximum.
of playlists for recording has reached the maximum.
The remaining recording capacity of the memory card for
the copy destination is insufficient.
An error has occurred on the memory card for the copy
destination while copying.
Loading of the scene file has failed.
Writing of the scene file has failed.
Due to an OS non-compatible error, 5 minutes has elapsed
until the service mode connection is established.
The unit tried to protect or delete a clip on a memory card
that has been locked.
The unit tried to copy a clip to the memory card that has
been locked.
It has tried to select more than 99 clips.
It has tried to delete a clip without choosing any.
It has tried to copy a clip without choosing any.
≥ Confirm if the system frequency of the clip is the same as
the system frequency of the unit.
≥ Check the clip.
≥ Match the device and content versions.
≥ Replace the memory card or delete unnecessary clips.
≥ Format it again.
≥ Copy to a card not containing a clip that is recorded over
multiple memory cards.
≥ Check the memory card.
≥ Check the memory card.
≥ Match the device and content versions.
≥ Cancel the protect on the clip.
≥ Restoring of the management information is performed
automatically after this.
≥ Match the device and content versions.
≥ Perform the setting after making it possible to set.
≥ Copy the clips other than the corresponding clip.
≥ Restoring of the management information is performed
automatically after this.
≥ Check the memory card.
≥ Replace the memory card in the copy destination or delete
unnecessary clips.
≥ Replace with a fully charged battery, or connect the AC
adaptor.
≥ Playback on a device that can playback.
≥ Copy the clips other than the corresponding clip.
≥ Operate after the operation becomes enabled.
≥ Replace the memory card or delete unnecessary clips.
≥ Replace the memory card or delete unnecessary clips.
≥ Select the clip to copy again, or secure enough space in
the remaining recording capacity on the memory card for
the copy destination.
≥ Confirm the memory card for the copy destination.
≥ Check the memory card.
≥ Check the memory card.
≥ Confirm if the OS in use is supported by the unit.
≥ Unlock the memory card.
≥ Execute the process such as copying by every 99 clips.
≥ Select a clip to be deleted.
≥ Select a clip to be copied.
- 190 -
Behavior and cause