Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Cadex Manuals
  4. Bicycle
  5. TRI
  6. User manual

Cadex TRI User Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
|ENGLISH|
|ENGLISH|
CADEX TRI USER MANUAL
CADEX TRI USER MANUAL
2.6.
1

Advertisement

loading

Summary of Contents for Cadex TRI

  • Page 1 |ENGLISH| |ENGLISH| CADEX TRI USER MANUAL CADEX TRI USER MANUAL 2.6.

  • Page 2: Table Of Contents

    |ENGLISH| CADEX TRI USER MANUAL TABLE OF CONTENTS Frame Sizing Stack And Reach Range Tri Bar Removal Assembly Top Tube Storage & Toolkit Removal & Installation Hydration System Seat Post & Saddle Adjustment...

  • Page 3: Frame Sizing

    |ENGLISH| CADEX TRI USER MANUAL 1. FRAME SIZING SIZING GUIDE AND GEOMETRY Sizing to be used as a reference only. Please check with a local authorized dealer to determine the correct size. Available sizes may vary from country to country.
  • Page 4 |ENGLISH| CADEX TRI USER MANUAL TOP TUBE LENGTH (mm) HEAD TUBE LENGTH (mm) HEAD TUBE ANGLE 71.0° 73.0° 73.0° 73.0° 73.0° FORK RAKE (mm) TRAIL (mm) 76.1 63.3 63.3 63.3 63.3 WHEELBASE (mm) 1005 1039 1072 CHAIN STAY LENGTH (mm)

  • Page 5: Stack And Reach Range

    |ENGLISH| CADEX TRI USER MANUAL 2. STACK AND REACH RANGE FIT DATA CHART GEOMETRY ARMREST STACK-MIN (mm) ARMREST STACK-MAX (mm) ARMREST REACH-MIN (mm) ARMREST REACH-MAX (mm) ARMREST STACK-MIN (mm) ARMREST STACK-MAX (mm) ARMREST REACH-MIN (mm)
  • Page 6 |ENGLISH| CADEX TRI USER MANUAL ARMREST REACH-MAX (mm) ARMREST STACK-MIN (mm) ARMREST STACK-MAX (mm) ARMREST REACH-MIN (mm) ARMREST REACH-MAX (mm) ARMREST STACK-MIN (mm) ARMREST STACK-MAX (mm) ARMREST REACH-MIN (mm) ARMREST REACH-MAX (mm)

  • Page 7: Tri Bar Removal Assembly

    |ENGLISH| CADEX TRI USER MANUAL 3. TRI BAR REMOVAL & ASSEMBLY REMOVAL 1. Install fork pads onto the upper part of fork (A). 2. Loosen but don't remove the four cockpit fixing bolts with a 4mm hex key (B). 3. Lift up the extension assembly and detach base bars from both sides. Install protective spacer to the four fixing bolts.
  • Page 8 |ENGLISH| CADEX TRI USER MANUAL ASSEMBLY NOTE: Always use a torque wrench. After assembly, with both wheels on the floor, hold both brakes and gently rock the bike forward and backward to make sure nothing is loose. 1. Remove securing Velcro strap from assembly (A).

  • Page 9: Top Tube Storage & Toolkit Removal & Installation

    |ENGLISH| CADEX TRI USER MANUAL 4. TOP TUBE STORAGE & TOOLKIT REMOVAL & INSTALLATION NOTE: Make sure all storage parts fit snugly to the frame and do not rattle. TOP TUBE STORAGE REMOVAL 1. Hold the lower end firmly and push upwards (A).
  • Page 10 |ENGLISH| CADEX TRI USER MANUAL TOOLKIT REMOVAL 1. Hold the lower end firmly and push upwards (A). 2. Pivot the toolkit sideways to remove (B). TOOLKIT INSTALLATION 1. Insert and firmly push upper latch into the frame recess (A). 2. Push tool box into the frame until it fits snugly. (B).

  • Page 11: Hydration System

    |ENGLISH| CADEX TRI USER MANUAL 5. HYDRATION SYSTEM REMOVAL & INSTALLATION REMOVAL 1. Remove front aero cover by pulling outward with both hands (A) 2. Take out the bladder and disconnect the straw. Replace the bladder (B). 3. Use your index finger to unclip the straw while pressing the clip with your thumb (C)
  • Page 12 |ENGLISH| CADEX TRI USER MANUAL INSTALLATION NOTE: Once the straw has been refitted, turn the handlebar from side to side to make sure is not compromised. If you feel any interference, remove the straw and refit again. 1. Feed the straw from the head tube trough the right-side of steerer (A).

  • Page 13: Seat Post & Saddle Adjustment

    |ENGLISH| CADEX TRI USER MANUAL 6. SEAT POST & SADDLE ADJUSTMENT CLAMP POSITION Front position 78° to 80° seat tube angle Rear position 76° to 78° seat tube angle...
  • Page 14 |ENGLISH| CADEX TRI USER MANUAL SADDLE CLAMP ADJUSTMENT 1. Remove saddle (A). 2. Loosen and remove both clamp fixing bolts (B). 3. Pull out clamp , turn it 180° horizontally and refit it into seat post (C). 4. Replace clamp fixing bolts , tighten to 5Nm (D).
  • Page 15 |ENGLISH| CADEX TRI USER MANUAL NOTE: 1. Always use a torque wrench 2. Once the installation or adjustment has been completed, grab the saddle and rock it back and forth to ensure all fasteners are snug. ➌ SADDLE POSITION ADJUSTMENT 1.
  • Page 16 |ENGLISH| CADEX TRI USER MANUAL SADDLE REMOVAL & INSTALLATION ➍ ➍ 1. Loosen and remove the side bolt (A). 2. Loosen and remove the top bolt and the upper piece (B). 3. Remove the saddle from the clamp. Rock the saddle back and forth to help removal. (C).
  • Page 17 |ENGLISH| CADEX TRI USER MANUAL ➌ 7. Refit saddle with the lower piece and lightly tighten the side bolt 8. Adjust saddle angle, fore and aft to preferred position (H). 9. Tighten the top bolt and the side bolt to 5 Nm (I) ➌...