ENGINE MANUAL PRODUCT REGISTRATION The engine on this unit is covered by a The Ariens dealer must register the product separate manual specific to the engine. This at the time of purchase. Registering the manual is included in the literature package product will help the company process that shipped with the unit.
(CARB) regulations. Tampering with emission controls and components by unauthorized personnel may result in severe fines or penalties. Emission controls and components can only be adjusted by an Ariens Company dealer or an authorized engine manufacturer's service center. Contact your Ariens Company Equipment Retailer concerning emission controls and components questions.
SAFETY Read these safety rules and follow them 4. Notice closely. Failure to follow these rules could NOTICE: Indicates information or procedures lead to loss of control of unit, severe personal that are considered important but not hazard injury or death to you or bystanders or result related.
Page 6
Safety Decal Description Do not operate mower 1. DANGER! unless guards are in operating position or entire bagger is attached. DANGER! 1.3 Tipping Hazard SERIOUS INJURY OR DEATH MAY RESULT FROM MACHINE Read and understand the ROLLOVER operator’s manual before operating unit.
SAFETY RULES Use extreme care when approaching blind corners, shrubs, trees, or other objects that This cutting machine is capable of amputating may block your view of a child. hands and feet and throwing objects. Failure to observe the following safety instructions Keep children out of the mowing area and in could result in serious injury or death.
Page 8
If you strike a foreign object, stop and Ariens dealer before using. inspect the machine. Repair, if necessary, before restarting. Be sure the area is clear of bystanders before operating.
Page 9
You could lose your footing the manufacturer’s recommended parts or balance. when necessary. Use only Ariens Company-recommended Fuel attachments that are appropriate to your use and can be used safely in your application. To avoid personal injury or property damage, use extreme care in handling gasoline.
Page 10
Service Maintain or replace safety and instruction labels, as necessary. Keep unit free of debris. Clean up oil or fuel spills. Do not change engine governor setting or overspeed the engine. Never make any adjustments or repairs with the engine (motor) running. *Disconnect the spark plug wire and ground against engine to prevent unintended starting.
ASSEMBLY Model 911173 CAUTION: AVOID INJURY. Read and understand the entire Safety section before proceeding. CARTON CONTENTS 1. Side Discharge Chute 2. Mulch Plug 3. Mower Unit 4. Literature Pack 1. Hardware 5. Grass Bag 2. Handlebar 6. Battery Charger (Models 911179, 190) Figure 4 7.
Page 12
Off position (stop sign). Engine must not start. If engine starts, stop engine by disconnecting spark plug while wearing gloves. Contact an authorized Ariens dealer for adjustment or repair. See Operator Presence Control (OPC) Handle on page 13.
If feature fails to operate, Models 911179, 190 disconnect spark plug wire and adjust as necessary or have the unit inspected and A removable key repaired by an authorized Ariens dealer operates the ignition before using. switch. Turn key 90° clockwise from the off...
Page 15
To drive forward: inspected and repaired by an authorized Slowly squeeze the wheel drive control lever Ariens dealer before using. toward the handlebar until you reach a comfortable ground speed. Hold the lever BLADE ENGAGED against the handlebar for full speed.
2. Remove fuel cap. replacement. Replace worn or IMPORTANT: Refer to engine manual for damaged bag with Ariens original correct type and grade of fuel. equipment replacement bag only. 3. Fill fuel tank to the bottom of filler neck.
1. Side Discharge Chute 2. Side Discharge 3. Tabs 1. Rear Door Figure 11 2. Bagger 3. Bag Mount To remove side discharge chute: 4. Mulch Plug 1. Lift side discharge cover. Figure 10 2. Lift side discharge chute off of tabs to release from mower and remove chute.
STARTING AND SHUT OFF Cutting Height Settings Chart Notch Cut grass length WARNING: Improper operation 25 mm (1") can lead to injury. Learn what the controls do and how they work. 38 mm (1 1/2") Thoroughly read and understand 51 mm (2") entire Operator Manual.
Shut Off 1. Park unit on a level surface, within reach of hose and in a location where the 1. Release wheel drive control lever and dispersal of wet grass clippings is allow unit to stop completely (self- acceptable. propelled models). 2.
MOWING TIPS Cut grass when it is dry. Keep mower blades sharp. Do not set cutting height too low. For tall grass, mow twice. Do not mow too fast. Mow with engine at full throttle. Discharge clippings into areas already cut. Vary cutting pattern with each mowing.
The engine and blade must stop within 3 seconds after releasing OPC handle. If the Ariens Dealers will provide any service, parts engine and blade continue to run, have the or adjustments which may be required to unit inspected and repaired before using.
CHECK MOWER BLADE 1. Remove mower blade from unit. Discard mower blade if: Check the torque of the bolt securing the • More than 1.3 cm (1/2") of metal is blade. removed. • For models 911175, 179, 188, 190 the •...
GENERAL LUBRICATION NOTICE: The mower transmission is lubricated and sealed at the factory. It should need no routine lubrication. If the transmission leaks grease, bring the mower to your local Ariens dealer for repair. EN - 21...
SERVICE AND ADJUSTMENTS CAUTION: AVOID INJURY. Read and understand the entire Safety section before proceeding. SERVICE POSITION Put unit into service position for easy access to bottom of deck. CAUTION: Avoid fuel spills. Follow steps below to help prevent fuel spills.
To position handlebar for storage: See Figure 18. 1. Push the operator presence control handle (operator presence control / blade brake clutch handle on Models 911177, 189) forward and rotate handlebar to desired position. WARNING: DO NOT operate unit with handlebar in storage position. Place handlebar in operating position before using.
Page 26
Remove Drive Belt Models 911177, 189 1. Remove two bolts from blade and remove blade. See Figure 21. 1. Blade Bolts 2. Blade Figure 21 2. Remove center bolt and hardware from BBC. See Figure 22. 1. Blade 2. Blade Adapter 3.
Page 27
4. Insert a 6 mm (1/4") prybar or similar tool into the hole in the clutch actuating lever. Pry lever to the right (clockwise) and disconnect cable spring from clutch lever. See Figure 23. 5. While holding anti-rotation arm in position with prybar, remove anti-rotation shoulder bolt.
(operator presence control / blade brake clutch handle on Models 911177, 189) has no user-serviceable adjustments. If releasing the handle does not stop the engine or blade within 3 seconds, take the unit to an authorized Ariens dealer for repairs. EN - 26...
ADJUST OPERATOR PRESENCE BATTERY CONTROL / BLADE BRAKE Models 911179, 190 CLUTCH (OPC / BBC) CABLE See Figure 27. Models 911177, 189 WARNING: AVOID INJURY. Read 1. Place unit in service position. See and understand the entire Safety Service Position on page 23. section before proceeding.
Charge Battery To Adjust: NOTICE: Engine does not charge the battery. 1. Stop engine and wait for all moving parts Battery will require periodic charging to to completely stop. ensure proper starting. It is recommended to 2. Clean any dirt or debris from the drive charge battery on a monthly basis for 6 hours components.
Cleaning SERVICE PARTS Allow unit to cool. Clean unit thoroughly with Always use genuine Ariens parts to keep mild soap and low pressure water. Brush off your mower running like new. dirt and debris from all surfaces. Touch up all scratched surfaces to prevent rust.
TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTION Engine will not 1. Fuel tank empty or low. 1. Check fuel level. Fill tank if start. necessary. 2. Spark plug wire loose or off. 2. Check connection. 3. Operator presence control 3. Check cable. Adjust, repair cable (operator presence or replace as necessary.
Register the product immediately at the time of sale. If the dealer does not register the product, the customer must complete the product registration card in the literature package and return it to the Ariens Company, or register the unit online at www.ariens.com, www.gravely.com, www.countax.com.
Page 36
Exclusions – Items Not Covered by This Warranty • Parts that are not genuine Ariens, Gravely or Countax service parts are not covered by this warranty and may void the warranty. • Damages resulting from the installation or use of any part, accessory, or attachment which is not approved by the Ariens Company for use with product(s) identified herein are not covered by this war- ranty.
Page 38
655 West Ryan Street Brillion, WI 54110 ariensco.com ariens.com...