Advertisement
Step 4 — Throughput Connections
NOTE:
See figure 5 for fiber cable connections. Connect the transmitter to a receiver in one of
three ways:
•
One way (transmitter to receiver) only, perform step 4a.
•
Two way (transmitter to receiver and return), perform steps 4a and 4b.
•
Output B is available to transmit 4K @ 60 Hz uncompressed signal when the FOX3
Uncompressed Video LinkLicense is purchased, perform step 4c.
a.
Connect the fiber between the A Out port on the transmitter and the A In port on the receiver (
NOTE:
Ensure that the transmitter and connected receiver are in the same transmission
mode, singlemode (SM) or multimode (MM) and use the correct SM or MM fiber cable to
connect the devices.
b.
To return serial data from the receiver (such as responses from a controlled device), IR data, or
returned audio to the transmitter, connect a cable between the A Out port on the receiver and A In
port on the transmitter (
c.
To transmit an uncompressed 4K @ 60 Hz signal, using the Uncompressed Video LinkLicense,
repeat step 4a on the SFP B port on the scaling receiver
SFP Link LEDs —
•
Transmit Optical OUT LED lights solid green when powered and lights off when there is no power on the endpoint.
Receive Optical IN LED lights solid green when light is present and lights off when there is no power or light present.
•
Step 5 — Power Connection
Connect the IEC power connector to the power inlet (see figure 1,
receiving power.
Operation
After the receiver, transmitter, and their connected devices are powered up, the system is fully operational. If any problems are
encountered, verify that the cables are routed and connected properly and the display device has a compatible resolution and
refresh rate. If problems persist, call the Extron S3 Sales & Technical Support Hotline (see the
Indications
A
Power LED — Indicates power is applied to the unit.
B
USB Config port — Connect a USB mini-B cable to
a computer to configure the device and update the
firmware via PCS or internal web pages.
C
INPUTS LEDs —
•
SIGNAL LED — Lights when the unit detects an
input video signal.
•
HDCP LED — Lights when the input signal is HDCP
encrypted.
D
USB LEDs —
•
USB HID Host LED — When the transmitter and
receiver are connected through the SFP port and a
host device is connected to the transmitter, the LED
remains lit to indicate an active connected device.
USB HID 1 and 2 LEDs —When an active USB peripheral device is connected to the HUB ports on the receiver, the
•
LED remains lit to indicate an active connected device.
•
USB 2.0 Host LED — When the transmitter and receiver are connected through the SFP port and a USB 2.0 Host
device is connected to the transmitter, the LED remains lit to indicate an active connected device.
•
USB 2.0 1 LED — When the transmitter and receiver are connected through the SFP port and a USB 2.0 Host device is
connected to the transmitter, the LED remains lit to indicate an active connected device.
2
).
A
on page 1). The power LED lights (
contact number
INPUTS
USB
HOST
1
2
SIGNAL
USB HID
CONFIG
HDCP
USB 2.0
A
A A
B B
B
C C
C
D
D D
INPUTS
USB
HOST
1
2
SIGNAL
USB HID
CONFIG
HDCP
Figure 6.
FOX3 SR 301 and FOX3 SR 311 Front Panels
OUTPUTS
B
A
OUT
IN
OUT
IN
Transmitter
1 1 1 1 1 1 1 1 1 1
2 2 2 2 2 2 2 2 2 2
1
).
2 2 2 2 2 2 2 2 2 2
1 1 1 1 1 1 1 1 1 1
INPUTS
A
B
Receiver
OUT
IN
OUT
IN
Figure 5.
Fiber Cable Connection
B
) when the unit is
on page 6).
MENU
F
FOX3 SR 301
ENTER
F
F F
E
E E
MENU
FOX3 SR 311
F
ENTER
3
Advertisement
