Table of Contents
Advertisement
TK-8108
2. Operation Features
The TK-8108 is a UHF FM radio designed to operate in
conventional format. The programmable features are sum-
marized.
3. Transceiver Controls and Indicators
3-1. Front Panel Controls
All the keys on the front panel are momentary-type push
buttons. The functions of these keys are explained below.
• POWER key
Transceiver POWER key. When the power is switched
off, all the parameters are stored in memory. When the
power is switched on again, the transceiver returns to the
previous conditions.
• CHANNEL Keys
• MONITOR key (Programmable)
•
key (Programmable)
• VOLUME UP/DOWN key
When the key is pressed, the volume level is increased/
decreased and repeats if held for 200ms or longer.
• BUSY/TX LED
The BUSY indicator (Green LED) shows that the channel
is in use. The TX indicator (Red LED) shows that you are
transmitting.
3-2. Programmable Keys
The FPU (KPG-70D) enables programmable keys to se-
lect the following functions.
•
Emergency
•
Key Lock
•
Monitor
•
Scan ON/OFF
• Emergency
Pressing this key for longer than 1 second causes the
transceiver to enter the emergency mode. The transceiver
jumps to the programmed "Emergency channel" and trans-
mits for 25* seconds.
The transceiver disables mic mute while transmitting.
After finishing transmission, the transceiver receivers for 5*
seconds. The transceiver Mute* the speaker while receiv-
ing. Following the above sequence, the transceiver contin-
ues to transmit and receive.
* Default value
• Key lock
Pressing this key causes the transceiver to accept entry
of only the [Vol Up/Down]*, [Key lock], Microphone [PTT],
[Monitor], [Emergency], and [Power] keys.
* Programmable
• Monitor
Used to release signalling (press once) or squelch (press
and hold for approximately two seconds) when operating as
a conventional. It is also used to reset option signalling.
• Scan ON/OFF
Press this key starts scanning. Pressing this key stops
scanning.
6
OPERATING FEATURES / 操作特性
•
Talk Around
•
Temporary Delete
•
None
•
Group
2. 操作特性
TK-8108是一种被设计为在常规格式下进行操作的UHF FM
无线电设备。可编程特性摘要如下。
3. 车载台控制和指示灯
3-1. 前面板控制
前端面板的所有按键均为短瞬型按键。这些按键的功能介
绍如下。
• 电源键
车载台电源按键。当关闭电源时，所有的参数，均被储存
在存储器中。当电源再次开启时，车载台回到先前的状态。
• 信道键
• 监听键 (可编程)
键 (可编程)
•
• 音量高/低键
按该键可以增大或减小音量，按下该键并保持200ms以上可
连续调节音量。
• 繁忙/发射指示灯
繁忙指示灯（绿色）表示信道正在使用中。发射指示灯
（红色）表示用户正在进行发射。
3-2. 可编程按键
FPU（KPG-70D）可以使可编程按键选择下述功能。
紧急报警
•
按键锁定
•
监听器
•
扫描 ON/OFF
•
• 紧急报警
按住此键1秒钟以上将使车载台进入紧急报警模式。车载台
将跳到已编程的"紧急报警组和信道"并且发射25*秒钟。
在发射过程中车载台不能保持话筒静音。发送结束后，车
载台接收5*秒钟。接收时车台机保持扬声器静音*。按照上述
顺序，车载台将连续发射和接收。
* 初始值
• 按键锁定
按此键使车载台只接收[音量高/低]*，[按键锁定]，话筒[通
话]，[监听器]，[紧急报警]和[电源]按键的输入。
* 可编程
• 监听器
当以常规方式操作时用于释放信令 (按一次) 或静噪抑制 (按
下并保持约两秒钟)。也用于复位可选信令。
• 扫描 ON/OFF
按此键开始扫描。再按此键停止扫描。
脱网
•
临时删除
•
无
•
组
•
Advertisement
Table of Contents
