Table of Contents
Advertisement
Parts and their functions (continued)
10.
RS‑232C connectors <RS‑232C IN/OUT>
Connects to an RS-232C cable.
RS-232C IN/OUT
Pin
connector appearance
No.
1
8
6
7
2
5
3
4
3
2
1
4
5
6
Mini Din 8-pin (JST)
7
8
<NOTE>
• Be aware that the polarities (+/-) of the serial data may be different
depending on the specifications of the device to be connected.
11.
LAN connector for IP control <LINK/ACT>
This LAN connector (RJ45) is connected when exercising IP control
over the unit from an external device. Use a cable with the following
specifications for the connection to this connector.
When using a PoE+ Ethernet hub
LAN cable
1
(category 5e or above, straight cable),
*
max. 100 m (328 ft)
When not using a PoE+ Ethernet hub
LAN cable
(category 5 or above, straight cable),
*
1
max. 100 m (328 ft)
*
1
Use of an STP (shielded twisted pair) cable is recommended.
12.
HDMI connector <HDMI>
This is the HDMI video output connector.
13.
Anti‑theft wire mounting hole
The anti-theft wire bracket (available from a hardware store) is
attached here.
14.
G/L IN connector <G/L IN>
This is the external sync signal input connector.
This unit supports BBS (Black Burst Sync) and tri-level
synchronization.
Supply to this connector the signals that correspond to the video
signal format which has been set.
Format
1080/59.94p
480/59.94i
1080/29.97p
480/59.94i
1080/23.98p
480/59.94i
1080/59.94i
480/59.94i
1080/29.97PsF
480/59.94i
1080/23.98PsF
—
720/59.94p
480/59.94i
480/59.94p(i)
480/59.94i
1080/50p
576/50i
1080/25p
576/50i
1080/50i
576/50i
576/50i
1080/25PsF
720/50p
576/50i
576/50p(i)
576/50i
<NOTE>
• Locking to a subcarrier is not possible with BBS.
15.
VIDEO OUT connector <VIDEO OUT>
This is the output connector used for monitoring the camera's
composite video signals. Use the monitor in the internal
synchronization mode.
Provide a BNC coaxial cable as the connecting cable.
There is a delay in the VIDEO OUT signal output by 120H (HD lines)
when at 720p and by 90H (HD lines) for any other.
16.
Hole used to secure cable cover
Use the screw provided to secure the cable cover.
RS‑232C IN
RS‑232C OUT
Pin
Signal
Signal
No.
DTR_IN
1
DTR_OUT
DSR_IN
2
DSR_OUT
TXD_IN
3
TXD_OUT
GND
4
GND
RXD_IN
5
RXD_OUT
GND
6
GND
IR OUT R
7
NC
IR OUT L
8
NC
External sync signal input format
BBS
Tri‑level sync
1080/59.94i
—
1080/59.94i
1080/59.94i
1080/59.94i
1080/23.98PsF
720/59.94p
—
1080/50i
—
1080/50i
1080/50i
720/50p
―
17.
SDI OUT connector <SDI OUT>
This is the SDI video signal output connector.
18.
DC IN connector <12V
Connect the AC adaptor supplied with the unit to this connector to
supply the DC 12 V voltage to the unit.
19.
Cable clamp
This is used to hold the cable connection to the DC IN connector and
prevent it from becoming disconnected.
20.
IR ID switches <IR ID>
CAM1
CAM2
These are used to select the ID of the wireless remote control
(optional accessory).
The IR ID switch settings "CAM1" to "CAM4" correspond to the
<CAM1> to <CAM4> buttons on the wireless remote control.
21.
Square holes (X2) for cable cover tabs
The tabs on the two sides of the cable cover are fitted into these
holes.
22.
AUDIO IN connector <AUDIO IN>
Inputs external audio (microphone, line).
23.
Ground connector
Connects to the ground connector on a wall outlet, ground bar, etc.
for grounding. "Note on grounding" (→ page 7)
24.
Tripod screw holes
(Screw: 1/4‑20 UNC, ISO 1222 (6.35 mm))
Use these screw holes when securing the unit to a tripod, etc.
25.
Service switches
SW1
SW2 SW3 SW4
ON
OFF
Function
SW1
Camera
address setting
SW2
(standard serial
SW3
communication)
SW4
Communication
format
SW5
Always leave at OFF (used for factory adjustments)
SW6
Infrared output
SW7
Communication
baud rate
SW8
Communication
connector
<NOTE>
• Perform switch settings before turning the unit on.
• Cameras whose camera address setting switches are set to AUTO
cannot coexist with cameras whose switches are set to 1 to 7.
• Manually setting multiple cameras to the same address will not
allow you to control multiple cameras from a single controller
simultaneously.
18
IN
>
CAM3
SW5 SW6 SW7 SW8
OFF
ON
See descriptions for SW1 to SW3
Panasonic
Standard serial
proprietary serial
communication
communication
Disable
Enable
9600 bps
38400 bps
RS-422
RS-232C
CAM4
Factory
settings
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Advertisement
Table of Contents
