Connecting the Units CAUTION: • PIONEER does not recommend that you install or service your display your- self. Installing or servicing the product may expose you to risk of electric shock or other hazards. Refer all installation and servicing of your display to autho- rized Pioneer service personnel.
Page 3
Note: • This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recre- ational vehicle, truck, or bus, check the battery voltage. • To avoid shorts in the electrical system, be sure to disconnect the ≠...
Connecting the Units Connecting the system Antenna jack IP-BUS input (Blue) Blue IP-BUS cable (supplied with XDV-P6) AV-BUS cable (supplied with XDV-P6) IP BUS STAND ALONE Hide-away unit (supplied with XDV-P6) AV-BUS cable (supplied with TV tuner) Blue AV-BUS input (Blue) Hide-away unit (supplied) Violet Blue...
Page 5
15 cm (5-7/8 in.) This product 40 cm (1 ft. 4 in.) Blue Optical cable (e.g. CD-AD600) (sold separately) 30-pin cable (supplied) 30-pin cable (supplied) IP-BUS cable (supplied with TV tuner) Hide-away TV tuner (e.g. GEX-P5700TV) Black (sold separately) Microphone/auxiliary input jack (3.5 ø) (MIC/AUX IN) Before installing this unit to your vehicle, pull out the jack to the place...
Connecting the Units Connecting the power cord (1) If this unit is used with more than a 6-ch speaker system, be sure to connect the yellow lead to the battery terminal directly. Black (ground) To vehicle (metal) body. Yellow After making all other connections to this unit, connect this to the positive + terminal of the battery.
Page 7
Yellow/black If you use an equipment with Mute function, wire this lead to the Audio Mute lead on that equipment. If not, keep the Audio Mute lead free of any connections. This product Fuse (7.5 A) Fuse resistor Fuse resistor Power supply box (supplied) Fig.
Connecting the Units Connecting the power cord (2) If this unit is used with more than a 6-ch speaker system, be sure to connect the yellow lead to the battery terminal directly. Connect when the audio settings of this product are used in the network mode. Left Tweeter (FRONT HIGH...
Page 9
WARNING LIGHT GREEN LEAD AT POWER CONNECTOR IS DESIGNED TO DETECT PARKED STATUS AND MUST BE CONNECTED TO THE POWER SUPPLY SIDE OF THE PARKING BRAKE SWITCH. IMPROPER CONNECTION OR USE OF THIS LEAD MAY VIOLATE APPLICABLE LAW AND MAY RESULT IN SERIOUS INJURY OR DAMAGE.
Connecting the Units When connecting to separately sold power amp Hide-away unit (supplied) See the section “Connecting the power cord (2)”. Blue/white To system control terminal of the power amp or Auto-antenna relay control terminal (max. 300 mA 12 V DC). System remote control Connect when the audio settings of this product are used in the network mode.
Page 11
RCA cables (sold separately) Front center speaker Left Tweeter Front middle range speaker Rear speaker Subwoofer Rear center speaker Power amp (sold separately) Power amp (sold separately) Power amp (sold separately) Power amp (sold separately) Power amp (sold separately) Power amp (sold separately) Right Tweeter...
Connecting the Units When connecting with a rear view camera When using this product with a rear view camera, automatic switching to video from a rear view camera when the gear shift is moved to REVERSE (R) position is possible. WARNING: •...
Page 13
Hide-away unit (supplied) CAUTION Pioneer recommends the use of a camera which outputs mirror reversed images, otherwise screen image may appear reversed. 15 cm (5-7/8 in.) Violet/white Of the two lead wires connected to the back lamp, connect the one in which the voltage changes when the gear shift is in the REVERSE (R) position.
Connecting the Units When connecting the external video component and the display Hide-away unit • It is necessary to set to AV INPUT in SETUP when connecting the external video com- ponent. When using a display connected to rear video output This product’s rear video output is for connection of a display to enable passengers in the rear seats to watch the DVD or Video CD.
Page 15
About video input Depending on the unit connected to this unit, video image may be distorted. In this case, eliminate the distortion by adjusting the video image selecting switch on the underneath of the hide-away unit to the appropriate position. Use a thin standard-tip screwdriver to adjust the video image selecting switch on the underneath of the hide-away unit.
Installation Note: • Before making a final installation of the unit, temporarily connect the wiring to confirm that the connections are correct and the system works properly. • Use only the parts included with the unit to ensure proper installation. The use of unautho- rized parts can cause malfunctions.
Mounting with Velcro Tape Thoroughly wipe off the surface before affixing the velcro tape. Hide-away unit Velcro tape (large) (hard) Velcro tape (large) (soft) Car mat or chassis DIN Front/Rear-mount This unit can be properly installed either from “Front” (conventional DIN Front-mount) or “Rear”...
Installation 2. Install the unit into the dash- board. (Fig. 15) After inserting the holder into the dashboard, then select the appropriate tabs according to the thickness of the dashboard material and bend them. (Install as firmly as possible using the top and bottom tabs.
• When installing in a shallow space, use the following screw holes. In this case, stick conceal tape on parts that protrude from the dashboard. Conceal tape Dashboard or Console Factory radio mounting bracket *2 If the screw holes of the bracket and the screw holes of this unit are not aligned, use a file to widen the screw holes of the bracket to match up the screw holes on this unit.
Page 20
à la batterie. Raccordements des appareils ATTENTION: • PIONEER ne vous recommande pas d’installer ou d’entretenir vous-même cet écran, car ces travaux peuvent présenter un risque d’électrocution ou d’autres dangers. Confiez tous les travaux d’installation et d’entretien de...
Page 21
Remarque: • Cet appareil est destiné aux véhicules avec une bat- terie de 12 V, avec pôle négatif à la masse. Avant de l’installer dans un véhicule de loisir, un camion ou un car, vérifier la tension de la batterie. •...
Raccordements des appareils Raccordement du système Jack d’antenne Entrée IP-BUS (Bleu) Bleu Câble IP-BUS (fourni avec le XDV-P6) Câble AV-BUS (fourni avec le XDV-P6) IP BUS STAND ALONE Appareil déporté (fourni avec le XDV-P6) Câble AV-BUS (fourni avec le syntoniseur de télévision) Bleu Entrée AV-BUS (Bleu) Appareil déporté...
Page 23
15 cm Cet appareil 40 cm Bleu Câble optique (par ex. CD-AD600) (vendu séparément) Câble péritel 30 broches (fourni) Câble péritel 30 broches (fourni) Syntoniseur de télévision déporté (par ex. GEX-P5700TV) (vendu séparément) Microphone/prise d’entrée auxiliaire (3,5 ø) (MIC/AUX IN) Avant d’installer cet appareil sur votre véhicule, placez la prise dans un endroit 1,5 m...
Raccordements des appareils Branchement du cordon d’alimentation (1) Si cet appareil est utilisé avec un système de haut-parleurs à plus de 6 voies, assurez-vous de raccorder le fil jaune directement à la batterie. Noir (masse) Fil de masse vers un élément en métal apparent de la voiture.
Page 25
Cet appareil Jaune/noir Si vous utilisez un appareil possédant une fonction de silencieux, reliez ce conducteur au conducteur de commande du silencieux de l’appareil en question. Sinon, ne reliez ce conducteur à rien. Boîtier d’alimentation (fourni) Fusible (7,5 A) Résistance fusible Résistance fusible Fig.
Raccordements des appareils Branchement du cordon d’alimentation (2) Si cet appareil est utilisé avec un système de haut-parleurs à plus de 6 voies, assurez-vous de raccorder le fil jaune directement à la batterie. Raccordez quand les réglages audio de cet appareil sont utilisés dans le mode réseau.
Page 27
AVERTISSEMENT LE FIL VERT CLAIR SUR LE CONNECTEUR D’ALIMENTATION A POUR BUT DE DETECTER L’ETAT DE STATIONNEMENT DU VEHICULE ET DOIT ETRE CONNECTE AU COTE ALIMENTATION DU COMMUTATEUR DU FREIN A MAIN. UNE CONNEXION OU UNE UTILISATION INCORRECTE DE CE FIL PEUT VIOLER LA LOI APPLICABLE ET PEUT ENTRAINER DES BLESSURES GRAVES OU DES DOMMAGES SERIEUX.
Raccordements des appareils Raccordements à un amplificateur de puissance vendu séparément Appareil déporté (fourni) Reportez-vous à la section “Branchement du cordon d’alimentation (2)”. Bleu/blanc Vers la borne de commande à distance de l’amplificateur de puissance ou vers la borne de commande du relais de l’antenne motorisée (max.
Page 29
Câbles à fiches Cinch (RCA) (vendu séparément) Haut-parleur central avant Gauche Haut-parleur d’aigus Haut-parleur médial avant Haut-parleur arrière Haut-parleur d’extrêmes graves Haut-parleur central arrière Amplificateur de puissance (vendu séparément) Amplificateur de puissance (vendu séparément) Amplificateur de puissance (vendu séparément) Amplificateur de puissance (vendu séparément) Amplificateur de...
Raccordements des appareils Raccordements à une caméra de recul Si vous utilisez cet appareil associé à une caméra de recul, la sélection automatique de la vidéo provenant de la caméra de recul est possible dès que le sélecteur de vitesse est placé sur la position REVERSE (R).
Page 31
Appareil déporté (fourni) PRÉCAUTION Pioneer conseille l’utilisation d’une caméra qui fournit des images inversées, comme dans un miroir; dans le cas contraire, l’image sur l’écran sera inverse. 15 cm Violet/blanc Des deux conducteurs connectés au feu de recul, connectez celui pour lequel la tension change quand le sélecteur de...
Raccordements des appareils Raccordements à un appareil vidéo externe et à un écran Appareil déporté • Il est nécessaire d’adopter l’option AV INPUT de SETUP si un appareil vidéo externe est connecté. Lors de l’utilisation d’un écran raccordé à la sortie vidéo arrière La sortie vidéo arrière de cet appareil est destinée à...
Page 33
À propos de l’entrée vidéo En fonction de l’appareil connecté à cet appareil, l’image vidéo peut être déformée. Dans ce cas, réglez le commutateur de sélection de l’image vidéo situé à l’arrière de l’appareil déporté sur la position correcte permettant d’éliminer la déformation. Utilisez un tournevis standard fin pour changer la position du commutateur de sélection de l’image vidéo à...
Installation Remarque: • Avant d’effectuer l’installation définitive, reliez provisoirement les appareils entre eux pour vous assurer qu’ils fonctionnent correctement, indi- viduellement et ensemble. • Pour obtenir une bonne installation, n’utiliser que les pièces de l’appareil. L’utilisation de pièces non prévues risque de causer un mauvais fonction- nement.
Fixation avec la bande Velcro Nettoyez soigneusement la surface avant de poser la bande Velcro. Appareil déporté Bande Velcro (grande) (rugueux) Bande Velcro (grande) (doux) Moquette ou châssis du véhicule Montage DIN avant/arrière Cet appareil peut être convenable installé en choisissant soit la méthode habituelle de montage par “l’avant”...
Installation 2. Installez l’appareil dans le tableau de bord. (Fig. 15) Après avoir introduit le support dans le tableau de bord, sélectíonnez les languettes appropriées en fonction de l’épaisseur du matériau du tableau de bord et courbez-les. (Assurez le maintien aussi solidement que possible en utilisant les languettes inférieures et supérieures.
• Lors de l’installation dans une cavité peu profonde, utilisez les perçages filetés ci-dessous. Dans ce cas, collez du ruban adhésif de masquage sur les parties qui dépassent du tableau de bord. Ruban adhésif de masquage Tableau de bord ou console Support de montage d’autoradio usine *2 Si les perçages du support et ceux de l’ap-...
Page 38
TEL: (03) 9586-6300 PIONEER ELECTRONICS OF CANADA, INC. 300 Allstate Parkway, Markham, Ontario L3R OP2, Canada TEL: 1-877-283-5901 PIONEER ELECTRONICS DE MEXICO, S.A. de C.V. Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270 <KMMNF> <06E00000>...