Table of Contents
Advertisement
Quick Links
Meraki Go GR10 Installation Guide
This guide describes the step-by-step process for installing the Meraki Go GR10 indoor WiFi access point.
The Cisco Meraki GR10 is a dual-band enterprise class 802.11ac cloud-managed access point.
Package Contents
The GR10 package contains the following:
• GR10 Cloud-Managed Access Point
• Mount plate
• Mount Kit
◦ Wall screws, wall screw anchors, and security screws
1
Advertisement
Table of Contents
Related Manuals for Cisco Meraki Go GR10
Summary of Contents for Cisco Meraki Go GR10
- Page 1 Meraki Go GR10 Installation Guide This guide describes the step-by-step process for installing the Meraki Go GR10 indoor WiFi access point. The Cisco Meraki GR10 is a dual-band enterprise class 802.11ac cloud-managed access point. Package Contents The GR10 package contains the following: •...
- Page 2 Understanding the GR10 Your Meraki GR10 has the following features:...
-
Page 3: Security Features
The mount plate has the following features: Security Features The GR10 features multiple options for physically securing the access point after installation: 1. Security screw – The accessory kit includes screws that can be used to secure the access point to the mount cradle. -
Page 4: Pre-Install Preparation
• Orange - AP is booting (permanent Orange suggests hardware issue) • Rainbow - AP is initializing/scanning • Blinking Blue - AP is upgrading • Green - AP in Gateway mode with no clients • Blue - AP in Gateway mode with clients •... -
Page 5: Collect Tools
Assigning IP Addresses to GR10s All gateway GR10s (GR10s with Ethernet connections to the LAN) must be assigned routable IP addresses. These IP addresses can be dynamically assigned via DHCP or statically assigned. Dynamic Assignment When using DHCP, the DHCP server should be configured to assign a static IP address for each MAC address belonging to a Meraki AP. -
Page 6: Collect Additional Hardware For Installation
2. Power over Ethernet supports a maximum cable length of 300 ft (100 m). 3. If being used in a mesh deployment, the GR10 should have line of sight to at least two other Meraki devices. A Cisco Partner can help ensure that your AP placement is ideal. - Page 7 Mount the GR10 Attach the GR10 to the Mount Cradle The GR10 attaches to the mount cradle with two tabs on the cradle that insert into the GR10, and is secured to the cradle using one screw. To attach the GR10 to the mount cradle properly, line up the top edge of the AP with the top tab of the mount cradle. Since the cradle is already mounted to the wall, guide the GR10 towards the top tab and insert the top tab into the GR10’s slot.
- Page 9 To release the GR10 from the mount cradle, first remove the security screw that secures the GR10 to the cradle’s bottom tab. While holding the GR10 with one hand, press the cradle’s bottom tab upwards, releasing the GR10 from the bottom of the cradle.
-
Page 10: Verify Device Functionality And Test Network Coverage
Secure the GR10 Depending on your mounting environment, you may want to secure the GR10 to its mount location. Your GR10 can be secured in several ways. If the GR10 has been installed using the mount cradle, it should be secured via security screw (Torx security screws are included) and/or Kensington lock. - Page 11 FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 12 (i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.