Dimensioned Drawings; I A Water Connections - Mitsubishi Electric CLIMAVENETA BRAN2 0021M Installation, User And Maintenance Manual

DIMENSIONED DRAWINGS

W1
= E
W4
A
Dimension
A
B
C
D
E
Weight distribution BRAT2
W1
W2
W3
W4
Total in operation
Weight distribution BRAN2
W1
W2
W3
W4
Total in operation
WATER CONNECTIONS
The choice and installation of components is the responsibil-
ity of the installer who should follow good working practice
and current legislation. Construction of a bypass is recom-
mended to enable the pipes to be washed through without
having to disconnect the unit (see drain valves).
The connection piping should be supported in such a way
as to avoid it weighing on the unit.
The following devices must be installed on the water circuit:
1. Two pressure gauges with a suitable scale (intake and
outlet);
2. Two vibration damper joints (intake and outlet);
3. Two shut off valves (normal in intake and calibrating in out-
let);
4. A flow switch on the unit outlet to the system circuit
(compulsory). The flow switch must be calibrated by
the installer to a value equal to 70% of rated flow.
5. Two thermometers (intake and outlet).
6. An intake filter must be installed as close as possible
to the evaporator and positioned to allow easy
access for routine maintenance. 500 micron filter
mesh.
7. All the pipes must be insulated with suitable material to
prevent the formation of condensate and heat loss. The
insulating material must be a vapour barrier. Make sure
that the control and shut-off devices protrude from the
insulation.
6 BRAT2 - BRAN2 EN
C
W2
=
B
W3
D
0021M-T 0025M-T 0031M-T 0041M-T 0051T
mm 900 900
mm 640 940
mm 370 370
mm 320 320
mm 580 580
0021M-T 0025M-T 0031M-T 0041M-T 0051T
kg 33 39
kg 12 14
kg 11 13
kg 29 34
kg 85 100
0021M-T 0025M-T 0031M-T 0041M-T 0051T
kg 37 43
kg 13 15
kg 13 15
kg 32 37
kg 95 110
600
0061T
900 900 900
940 1240 1240
370 370 370
320 320 320
580 580 580
0061T
41 49 57
14 18 20
14 16 19
36 42 49
105 125 145
0061T
45 55 62
16 20 23
15 17 21
39 48 54
115 140 160
8. At the lowest points in the system, install drain valves for
easy emptying.
9. At the highest points in the system, install automatic or
manual air vent valves.
Failure to install the flow switch will mean the heat exchang-
er is not protected in the event of no flow of liquid.
Climaveneta cannot be held liable for any damage to the
unit and/or the system following the failure to install these
devices or the filter.
The correct operation of the components that help ensure
the safety of the appliance and the system should be
checked regularly.
Specifically, this involves cleaning the filters and checking
the operation of the flow switches installed.
Water flow to the chiller unit must conform to the values
shown in the section on "General Technical Data".
The flow of water must be maintained constant during oper-
ation.
The water content of the unit must be such as to avoid dis-
turbing operation of the refrigerant circuits.
400
0071T 0091T
900 1450 1450
1390 1200 1200
420 550 550
370 497 497
580 1477 1477
0071T 0091T
60 83 84
22 42 43
20 39 40
53 81 83
155 245 250
0071T 0091T
66 92 93
24 43 44
22 40 41
58 90 92
170 265 270
I
0101T 0121T
1450 1450
1700 1700
550 550
497 497
1477 1477
0101T 0121T
110 111
54 55
51 52
105 107
320 325
0101T 0121T
119 120
55 56
52 53
114 116
340 345
I A