I A Receiving, Handling And Installing The - Mitsubishi Electric CLIMAVENETA BRAN2 0021M Installation, User And Maintenance Manual

RECEIVING, HANDLING AND INSTALLING THE PRODUCT
The chillers are supplied accompanied by:
- installation, user and maintenance manual;
- CE declaration;
CHOICE OF INSTALLATION SITE
Before installing the unit, agree with the customer the site
where it will be installed, taking the following points into con-
sideration:
• Check that the fixing points are adequate to support the
weight of the unit;
• Pay scrupulous respect to safety distances between the
unit and other equipment or structures to ensure that air
entering the unit and discharged by the fans is free to cir-
culate.
HANDLING AND POSITIONING
The unit should always be handled by qualified personnel
using equipment adequate for the weight of the chiller.
• Before handling the unit, check the capacity of the lift
equipment used, respecting the instructions on the pack-
aging.
• To move the unit horizontally, make appropriate use of a
lift truck or similar, bearing in mind the weight distribution
of the unit.
To lift the unit, insert tubes long enough to allow position-
ing of the lifting slings and safety pins in the special feet
on the unit.
For the sizes of these tubes, see the figures shown in the
corresponding section.
BRAT2 Dimensions and weight with standard packaging
Size 0021M-T
Dimension L mm
Dimension P mm
Dimension H mm
Weight Kg
BRAN2 Dimensions and weight with standard packaging
Size 0021M-T
Dimension L mm
Dimension P mm
Dimension H mm
Weight Kg
BRAT2 Dimensions and weight with wooden crate
Size 0021M-T
Dimension L mm
Dimension P mm
Dimension H mm
Weight difference Kg
BRAN2 Dimensions and weight with wooden crate
Size 0021M-T
Dimension L mm
Dimension P mm
Dimension H mm
Weight difference Kg
4 BRAT2 - BRAN2 EN
Barcode
(compressor side)
0025M-T 0031M-T
970 970 970
480 480 480
840 1140 1140
100 115 120
0025M-T 0031M-T
970 970 970
480 480 480
840 1140 1140
110 125 130
0025M-T 0031M-T
1070 1070 1070
580 580 580
890 1190 1190
120 140 145
0025M-T 0031M-T
1070 1070 1070
580 580 580
890 1190 1190
130 150 155
• To avoid the slings damaging the unit, place protection
between the slings and the unit.
Position the unit in the site indicated by the customer.
Place either a layer of rubber (min. thickness 10 mm) or
vibration damper feet (optional) between the base and
support surface.
Fix the unit, making sure it is level and that there is easy
access to water and electrical components.
If the site is exposed to strong winds, fix the unit ade-
quately using tie rods if necessary.
If a heat pump unit is being installed, make sure the conden-
sate is drained using the drain hose supplied as standard.
Prevent leaves, branches or snow from accumulating around
the unit. These could reduce the efficiency of the unit.
The installation, user and maintenance manual is an
integral part of the unit and should therefore be read and
kept carefully.
It is recommended that the packaging should not be
removed until the unit is located in the installation site.
During transport, the chiller should be kept in a verti-
cal position
The weight of the chiller is biased towards the com-
pressor side (side of the packaging with the barcode,
see the figure at the foot of the page).
Do not dispose of packaging materials in the environ-
ment or leave them within reach of children as they may
represent a hazard.
0041M-T 0051T 0061T
970 970 970
480 480 530
1440 1440 1590
145 165 175
0041M-T 0051T 0061T
970 970 970
480 480 530
1440 1440 1590
160 180 190
0041M-T 0051T 0061T
1070 1070 1070
580 580 630
1490 1490 1640
175 195 215
0041M-T 0051T 0061T
1070 1070 1070
580 580 630
1490 1490 1640
190 210 230
BRAT(N)2 0021÷0061: Ø 22mm
BRAT(N)2 0071÷0121: Ø 25mm
0071T 0091T 0101T
1530 1530 1530
650 650 650
1400 1400 1900
260 265 340
0071T 0091T 0101T
1530 1530 1530
650 650 650
1400 1400 1900
280 285 360
0071T 0091T 0101T
1630 1630 1630
750 750 750
1450 1450 1950
305 310 395
0071T 0091T 0101T
1630 1630 1630
750 750 750
1450 1450 1950
325 330 415
I A
0121T
1530
650
1900
345
0121T
1530
650
1900
365
0121T
1630
750
1950
400
0121T
1630
750
1950
420