Table of Contents
Advertisement
Features
YOUR BREVILLE AIR PURIFIER
Your Breville Smart Air
Connect Purifier
TM
improves your indoor air quality using
4 distinct levels of protection.
1. A Pre-Filter
Captures larger airborne particles such as
human hair, pet dander and dust particles.
2. A True HEPA Filter
Traps up to 99.97% of allergens and
airborne contaminants down to 0.3 microns
in size. These include lung-damaging dust,
mould spores, plant spores, and pollen.
3. An Activated Carbon Membrane
Along with assisting in the capture of
dust, smoke, pollen and other airborne
allergens, the activated carbon membrane
helps to neutralise odours in the home and
to eliminate fumes emitted by household
products as well as other volatile organic
compounds (VOC's) that might be found
in the air.
4. Microbe Shield
TM
Technology
Microbe Shield
technology uses a
TM
shortwave UV-C light specially designed
to target germs and bacteria from the
incoming air as it passes through the air
purifier before releasing the air back into
the surrounding area. The Microbe Shield
function can be turned on and off according
to preference.
8
Assembly
BEFORE FIRST USE
• Remove and safely discard any packaging
material or promotional labels attached to
your air purifier and filter.
• Remove the filter from the air purifier
(see REPLACING THE FILTER on page 11)
and take it out of the plastic bag. Then
re-insert the filter into the air purifier.
• Select a flat and level location for the
air purifier.
• For proper air flow, locate the unit at least
20cm from any wall or furniture.
• Ensure the air inlet and outlets are not
blocked before use.
• Plug the power plug into a 230V OR 240V
power outlet and turn on the power outlet.
IMPORTANT
When moving the air purifier, always lift the
unit using two hands and set down gently on
a flat and level surface.
TM
Functions
OPERATING YOUR AIR PURIFIER
1. Press the
POWER button to turn on and
the On/Wi-Fi reset light will illuminate.
2. The air quality sensor light will illuminate,
usually starting with a blue light until it has
time to sense the air quality and then it may
change to an alternate colour.
3. To adjust how the air purifier operates,
follow the directions below.
SensAir
LIVE PURITY CONTROL
TM
• Your Breville Smart Air
Connect Purifier has
TM
a built-in air quality sensor to detect changes
to air quality in the surrounding area.
• The SensAir
indicator light around the
TM
control panel will change colours according
to the quality of the surrounding air.
Grade
Air Quality
Colour of Light
1
Very Good
Blue
2
Good
Yellow
3
Fair
Orange
4
Poor
Red
/NIGHT MODE/
Microbe Shield
TM
RESET FILTER
The Microbe Shield
Mode, Night Mode
TM
and Reset Filter utilise the same button on
the control panel. Pressing the
Microbe
Shield
/NIGHT/RESET FILTER button will
TM
cycle through the Microbe Shield
and Night
TM
Modes.
Microbe Shield
TM
• Press the
Microbe Shield
/NIGHT MODE/
TM
RESET FILTER button until the Microbe
Shield
indicator light illuminates to turn
TM
on.
Microbe Shield
TM
• To turn off the Microbe Shield
during night
TM
mode, press the Microbe Shield
/NIGHT
TM
MODE/RESET FILTER button again. Microbe
Shield
will turn off automatically, and the
TM
lights will remain dimmed.
• To turn off night mode, press the Microbe
Shield
/NIGHT MODE/RESET FILTER
TM
button again. All lights should return to normal.
• Alternatively, press again until the light
extinguishes to turn off this function.
Filter Reset
• When the filter reset light blinks continuously,
this is indicating that the filter needs to
be replaced.
• To reset the indicator after the filter has been
replaced, press and hold the Microbe Shield
Night Mode/Filter Reset button for 5 seconds
and the filter reset light will turn off.
Night Mode
• To turn on Night Mode, press the
Microbe
Shield
/NIGHT MODE/RESET FILTER
TM
button until the night indicator light starts
to blink.
• After 10 blinks, all indicator lights on
the control panel will turn off as the unit
enters night mode and the fan speed will
automatically change to Low.
• Press any button on the control panel to
re-engage the control panel and turn off night
mode. The indicator light will extinguish.
/
TM
9
Advertisement
Table of Contents
