Residual Risks; Risk Reduction - Ryobi ROS310-SA20 Original Instructions Manual

Safety, performance, and dependability have been given
top priority in the design of your random orbital sander.
INTENDED USE
The random orbital sander is intended to be used only
by adults who have read and understood the instructions
and warnings in this manual, and can be considered
responsible for their actions.
wood, plastic, or similar materials using the abrasive
pads provided. The product should only be used in well
ventilated areas.
The product is designed for dry sanding only. Do not use
for wet sanding.
The product is intended for consumer use only.
Do not use the product for any other purpose. Use of the
product for operations different from intended could result
in a hazardous situation.
WARNING
Dust from certain paints, coatings, and other materials
may cause irritation or allergic reactions. Dust from
wood, such as oak, beech, MDF, and similar materials
be allowed to use the product on materials containing
asbestos.
WARNING
Do not use compressed air to remove dust from the
product. Dirt and grit blown away by compressed air can
cause serious eye injury.
WARNING
Read all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may result in
Save all warnings and instructions for future reference.
RANDOM ORBITAL SANDER SAFETY WARNINGS
Clamp workpiece with
Unclamped workpieces can cause severe injury and
damage. Do not hold the material you are sanding by
hand.
Do not use sanding paper larger than needed. Extra
paper extending beyond the sanding pad can also
cause serious lacerations.
Always wear safety goggles and a dust mask when
sanding, especially when sanding overhead.
A suitable breathing respirator must be worn while
sanding lead paint, some woods, and metal to avoid
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise and the operator
should pay special attention to avoid the following:
It has been reported that vibrations from handheld tools
may contribute to a condition called Raynaud's Syndrome
in certain individuals. Symptoms may include tingling,
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking and work practices
are all thought to contribute to the development of these
symptoms. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:
If you experience any of the symptoms of this condition,
immediately discontinue use and see your doctor about
these symptoms.
a clamping device.
See page 81.
1. Power cord sleeve
2. Speed control dial
3. Live tool indicator
4.
5. Sander cover
6. Dustbox cover
7. Dustbox container

RESIDUAL RISKS

Injury caused by dust
– Using the product will produce considerable amount
of dust and fine particles. Use the dust collection
device or connect a dust extraction vacuum when
operating the product. Wear dust masks containing
filters appropriate to the materials being worked
on. Ensure adequate workplace ventilation. Do not
eat, drink, or smoke in the work area. Only operate
on materials which are specified in the Intended
use section. Do not operate on materials (e.g.,
asbestos) which present a health hazard.
Injury caused by noise and vibration
– Wear ear protection during the sanding operation.
Do not operate the product for long periods of time.
See "Risk reduction".

RISK REDUCTION

Keep your body warm in cold weather. When operating
the unit wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud's Syndrome.
After each period of operation, exercise to increase
blood circulation.
Take frequent work breaks. Limit the amount of
exposure per day.
WARNING
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
KNOW YOUR PRODUCT
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
English | 1