Bosch PROFESSIONAL GST 65 Operating Instructions Manual page 10

OBJ_BUCH-286-001.book Page 10 Tuesday, October 24, 2006 12:54 PM
Parallel Guide with Circle Cutter (Accessory)
For cuts using the parallel guide with circle cutter 17
(accessory), the thickness of the material must not
exceed a maximum of 30 mm.
Parallel cuts (see figure F): Loosen the locking screw
16 and slide the scale of the parallel guide through the
lead 15 in the base plate. Set the desired cutting width
as the scale value on the inside edge of the base plate.
Tighten the locking screw 16.
Circular cuts (see figure G): Set the locking screw 16
to the other side of the parallel guide. Slide the scale of
the parallel guide through the lead 15 in the base plate.
Drill a hole in the workpiece centered in the section to
be sawn. Insert the centering tip 18 through the inside
opening of the parallel guide and into the drilled hole.
Set the radius as the scale value on the inside edge of
the base plate. Tighten the locking screw 16.
Coolant/Lubricant
When sawing metal, coolant/lubricant should be
applied alongside cutting line because of the material
heating up.
Maintenance and Service
Maintenance and Cleaning
Before any work on the power tool itself, pull
the mains plug.
For safe and proper working, always keep the
power tool and the ventilation slots clean.
Clean the saw blade holder regularly. For this, remove
the saw blade from the machine and lightly tap out the
power tool on a level surface.
Heavy contamination of the power tool can lead to mal-
functions. Therefore, do not saw materials that produce
a lot of dust from below or overhead.
In extreme working conditions, conductive
dust can accumulate in the interior of the
power tool when working with metal. The pro-
tective insulation of the power tool can be
degraded. The use of a stationary extraction
system is recommended in such cases as well
as frequently blowing out the ventilation slots
and installing a ground fault circuit inter-
rupter (GFCI).
Lubricate the guide roller 4 occasionally with a drop of
oil.
Check the guide roller 4 regularly. If worn, it must be
replaced through an authorized Bosch after-sales ser-
vice agent.
10 | English
If the power tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service center for
Bosch power tools.
In all correspondence and spare parts orders, please
always include the 10-digit article number given on the
type plate of the power tool.
Service and Customer Assistance
Exploded views and information on spare parts can be
found under:
www.bosch-pt.com
In case of a claim, repair or purchase of replacement
parts or in case of queries or other problems, please
contact your local dealer or Bosch representative.
People's Republic of China
Website: www.bosch-pt.com.cn
China Mainland
Bosch Power Tools (China) Co., Ltd.
567, Bin Kang Road
Bin Jiang District 310052
Hangzhou, P.R.China
Service Hotline: . . . . . . . . . . . . . . . . . . 800 8 20 84 84
✆ . . . . . . . . . . . . . . . . . . . . . . . . +86 571 87 77 43 38
Fax . . . . . . . . . . . . . . . . . . . . . . . . +86 571 87 77 45 02
HK and Macau Special Administrative Regions
Melchers (H.K.) Ltd, Room 1210
Shun Tak Centre, West-Tower
168 – 200 Connaught Road, Central Hong Kong
Customer Service Hotline: . . . . . . .+852 25 89 15 61
Fax . . . . . . . . . . . . . . . . . . . . . . . . . . . +852 25 48 79 14
E-Mail: bosch@melchers.com.hk
Indonesia
P. T. Multi Tehaka
Karang Anyar Permai Block B-24
Jl. Karang Anyar No. 55
Jakarta Pusat 10740
Indonesia
✆ . . . . . . . . . . . . . . . . . . . +62 21 6 59 52 22 (5 lines)
Fax . . . . . . . . . . . . . . . . . . . . . . . +62 21 6 59 52 52 – 3
sales@bosch.co.id
www.bosch.co.id
Phillippines
Robert Bosch, Inc.
Zuellig Building
Sen. Gil Puyat Avenue
Makati City 1200, Metro Manila
Philippines
✆ . . . . . . . . . . . . . . . . . . . . . . . . . . . +63 2 8 17 32 31
www.bosch.com.ph
1 609 929 K70 • 24.10.06