Wall Mounting; Assembly And Adjustments; Operation - Craftsman CMCE521 Instruction Manual

Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaning solutions.

Wall Mounting

Some CRAFTSMAN chargers are designed to be wall
mountable or to sit upright on a table or work surface. If wall
mounting, locate the charger within reach of an electrical
outlet, and away from a corner or other obstructions which
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the wall.
Mount the charger securely using drywall screws (purchased
separately) at least 1" (25.4 mm) long, with a screw head
diameter of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
nOTE: Do not attempt to mount CMCB101 charger under a
bench or table.
nOTE: Only mount CMCB101 charger with the charging
lights pointed upward toward the ceiling.
VersaTrack™

WARNING: Do not charge batteries while charger is
hung on Trackwall.
CRAFTSMAN chargers, except the CMCB101, can
be stored on CRAFTSMAN VersaTrack™ Trackwall.
Hooks and accessories are sold separately. Please
refer to the VersaTrack™ Trackwall accessory sheet for
further information.
nOTE: The CMCB101 charger is not CRAFTSMAN VersaTrack™
Trackwall compatible.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. These tools are factory tested; if
this tool does not operate, check power supply.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
Storage (Fig. A)
Accessory and Air hose storage
The accessories 8 , 9 , and
unit inside the accessory storage
When inflator is not in use, press the high-pressure air
hose into the hose storage area
2
When inflator is not in use, place the accessories into the
storage area located on top of the tool.
10 are stored on the top of the
7 area.
at the base of the tool.
6
Fitting the Accessories (Fig. A, H–J)
Your inflator is supplied with a high-pressure tapered nozzle
adaptor 8 , an inflator needle adaptor
adaptor 10 , located on the top of the tool in the accessory
storage 7 area.
1. To use the air chuck
3
up position.
2. Place the air chuck over the stem of the inflator needle
adaptor, high-pressure tapered nozzle adaptor, or the
Presta valve adaptor.
3. Press the lever on the air chuck down to lock it
13
in place.
4. Place the inflator needle adaptor, high-pressure tapered
nozzle adaptor, or the Presta valve adaptor into the item
to be inflated.
nOTE: Always make sure that the lever is in the up position
when not in use. When operating your inflator with an
accessory, use only the accessories sold with this unit.
nOTE: Make sure the inflator needle adaptor or other
accessories are firmly locked in place before turning the
inflator on.

OPERATION


WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Installing and Removing the Battery Pack
(Fig. A, E)

WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
nOTE: For best results, make sure your battery pack is
fully charged.
1. To install the battery pack
the battery pack with the rails inside the tool's handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
2. To remove the battery pack from the tool, press the
battery pack release button
battery pack out of the tool handle. Insert it into
the charger as described in the charger section of
this manual.
Proper Hand Position (Fig. G)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the handle
9 , and a Presta valve
, make sure the lever is in the
into the tool handle, align
11
12 and firmly pull the
English
.
5
9