Summary of Contents for Impex MARCY DIAMOND ELITE MD-856
Page 1
Safety Notice Hardware Identifier MD-856 Assembly Instruction Parts List Warranty Ordering Parts Model MD-856 Retain This Manual for Reference 07-26-05 OWNER'S IMPEX INC. MANUAL 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.com...
ORDERING PARTS..................………… 13 BEFORE YOU BEGIN Thank you for selecting the Marcy Diamond Elite MD-856 BENCH by IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction.
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
Page 4
WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Front Stabilizer. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown...
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Note: Do not tighten all nuts and bolts until instructed to do so. B.) Attach the Left Upright Beam (#1) to a Rear Stabilizer (#3).
Page 8
STEP 2 (See Diagram 2) A.) Slide the Sliding Block (#15) onto the Main Seat Support (#4). Thread a Lock Knob (#42) into the selected hole to hold the Sliding Block in position. B.) Attach the Leg Developer Holder (#13) to the Front Stabilizer (#14). Secure it with three M10 x 5/8”...
Page 9
STEP 3 (See Diagram 3) A.) Attach the holes on the end of the Backrest Supports (#21) to the long pivot on the Sliding Block (#15). Attach the Backrest Board (#26) to the Backrest Supports. Secure it with four M8 x 1 5/8” Allen Bolts (#65) and Ø5/8” Washers (#67). Place the Backrest Board rest against the Backrest Adjustment Bar.
Page 10
STEP 4 (See Diagram 4) A.) Insert the U-shaped Pin (#49) into the open slot on the Leg Developer Holder (#13). Secure it with one M6 x ½” Philips Screw (#47), Ø ½” Washer (#48), and Spring (#50). B.) Attach the Leg Developer (#10) to the Leg Developer Holder. Secure it with an Axle (#55), two M10 x 5/8”...
Page 11
STEP 5 (See Diagram 5) A.) Attach the Arm Curl Pad (#28) to the Arm Curl Stand (#9). Secure it with two M8 x 5/8” Allen Bolts (#64) and Ø 5/8” Washers (#67). B.) Insert the Arm Curl Stand into the top opening on the Leg Developer Holder. Use a Lock Knob (#42) to secure the Stand.
PARTS LIST KEY NO. DESCRIPTION Q’ty Left Upright Beam Right Upright Beam 4 ½” L-shaped Pin Rear Stabilizer 3” L-shaped Pin Main Seat Support 4” L-shaped Pin Cross Brace Spring Clip Backrest Adjustment Bar Axle Squat Bar Catch M10 x 3 ½” Carriage Bolt Rear Diagonal Support M10 x 2 ¾”...
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the customer. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for commercial or rental purposes.