Table of Contents
Advertisement
English
1600KG- LOW PROFILE STEEL SERVICE JACK
STHT82942
Congratulations!
You have chosen a Stanley tool. Years of experience, thorough
product development and innovation make Stanley one of the
most reliable partners for professional tool users.
Technical Data
Capacity
Lifting Range Min.
Lifting Range Max
Jack Dimensions
Head Cap Diameter
Handle Length
WARNING: To reduce the risk of injury, read the
instruction manual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
these symbols.
DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
property damage.
Denotes risk of electric shock.
Denotes risk of fire.
GENERAL SAFETY INSTRUCTIONS
IMPORTANT SAFETY CONSIDERATIONS
WARNING: Before operating this device, be sure to read all
content within this manual, ensuring that you understand
the operating procedures, maintenance requirements and
all safety warnings. All users shall have an understanding
of the product, its operating characteristics, and safety
operating instructions before operating this device. Safety
information shall be emphasized and understood.
2
STHT82942
kg
1600
mm
85
mm
375
mm
560 x 220 x 133
mm
54
mm
645
WARNING:
•
Study, understand, and follow all instructions before operating
this device. Do not exceed the rated capacity stated.
•
Use only on a hard level surface and ensure it is free to roll
during lifting and lowering.
•
Locate the load centrally on the saddle.
•
Consult the vehicle owner's manual prior to lifting the vehicle
and conduct a pre-operational check of the equipment.
•
Support the vehicle with appropriate means immediately
after lifting.
•
Do not move or dolly the vehicle while it is on the jack.
•
Lift only on areas of the vehicle as specified by the
vehicle manufacturer.
•
No modifications shall be made to this product.
•
Failure to heed these markings may result in serious personal
injury/ property damage.
•
Ensure that there are no persons inside the vehicle to be lifted.
Switch off the engine and apply the brake. Ensure the vehicle,
or elements of the vehicle, to be lifted cannot move during
lifting operations. Use chocks if necessary.
•
Do not enter the vehicle or start the engine while it is
supported on the jack or appropriate stands.
•
The hydraulic trolley jack is a lifting and lowering device only
and should never be used to move the vehicle.
•
The hydraulic trolley jack should be positioned so as to avoid
the need for the user to introduce any part of his/her body
underneath the vehicle. Never work under a raised vehicle
without previously supporting it with mechanical stands or
other appropriate methods. Never position any part of your
body near the movable elements of the hydraulic trolley jack.
•
If the device jams, lift the vehicle with another jack until the
first can be cleared.
•
As an additional safety measure against overload, the
hydraulic trolley jack is fitted with an overload valve set at
the factory and which should not be adjusted under any
circumstances. If nominal capacity of the hydraulic trolley jack
is exceeded the overload valve will stop the lifting operation.
•
Never use this hydraulic trolley jack to lift persons.
•
Never use this hydraulic trolley jack as a handling means (for
moving loads).
•
When the hydraulic trolley jack is not in use, make sure the
lifting arm is fully retracted to avoid corrosion.
•
Avoid any contact between the hydraulic trolley jack and food.
Users should not eat food after it has come in contact with the
hydraulic trolley jack.
•
This hydraulic trolley jack is designed to be used with a 54mm
diameter head cap, and a handle of 645mm in length
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Advertisement
Table of Contents
