JVC GR-SXM540 Instructions Manual page 24

USING THE REMOTE CONTROL UNIT (GR-SXM745 only)
Make sure the remote control is pointed at the remote sensor
Pla yba c k Z oom
To magnify the recorded image up to 10X at any
time during playback. Make sure that the TBC
mode is activated.
T
1) Press PLAY to find the scene of interest.
2) Press ZOOM (T/W)
end zoom press and hold W until magnification
returns to normal. Or, press STOP
T
press PLAY .
• Due to digital image processing, the quality of the
image may suffer.
Anim a t ion And T im e -La pse
The remote control lets you set/release interval
time and recording time without setting REC TIME/
INT. TIME ( pg. 21) in SYSTEM MENU.
Animation
O
Each time ANIM.
changes in the following order: 1/4S, 1/2S, 1S, 5S
and no indication (off).
Time-Lapse
Each time REC TIME
time changes in the following order: 1/4S, 1/2S,
1S, 5S and no indication (off). Each time INT. TIME
f
is pressed, the interval time changes in the
following order: 15S, 30S, 1MIN, 5MIN and no
indication (off).
I nse rt Edit ing
You can record a new scene onto a previously
recorded tape. Only the video signal is recorded in
this mode.
1) Set the Power Switch
2) Play back the tape, locate the edit-out point and
s
press PAUSE
)
for more than 1 second to reset the tape
counter, then press it again for less than
1 second so that "M" appears.
Y
3) Press REW to go a little beyond the beginning
of the scene you want to replace, press PLAY
to view the recorded tape, and press PAUSE
exactly at the edit-in point where the new scene
should start.
4) While holding down INSERT
release PAUSE
Downloaded from:
R
. Pressing T zooms in. To
U
is pressed, the recording time
O
is pressed, the recording
@
to " ".
. Press and hold COUNTER R/M
I
, press and
s
. w appears.
https://www.usersmanualguide.com/
5) To begin Insert Editing, press START/STOP
When the counter reaches "0:00:00", editing
stops automatically and the camcorder enters
the Insert-Pause mode. To end Insert Editing,
press STOP
• During Insert Editing, the original audio will be
heard from the speaker.
• After step 4), "Retake" (
and then
performed.
• The tape may stop slightly before or after the
designated end point, and noise bars may appear.
Neither indicates a defect in the unit.
Audio Dubbing
You can record a new soundtrack on a
prerecorded tape (normal audio only). The sound
is recorded from the built-in microphone.
Perform steps 1) and 2) of the Insert Editing
procedure.
3) Press REW
of the scene onto which you want to dub the new
audio, press PLAY
then press PAUSE
dubbing should start.
4) While holding down A. DUB
release PAUSE
5) To begin Audio Dubbing, press PLAY
the counter reaches "0:00:00", Audio Dubbing
stops automatically and the camcorder enters
the Audio Dub-Standby mode. To end Audio
Dubbing, press STOP
• Do not press REW
Standby, or the edit points will not be accurate.
• If the microphone is too close to the TV, or if the
TV's volume is too high, whistling or howling may
occur.
For Insert Editing/Audio Dubbing
• Insert Editing and Audio Dubbing may not work
correctly if the tape contains blank segments, or if
T
the recording speed was changed during the
s
original recording.
• To edit/dub onto a tape, make sure the erase
protection tab is in the position that allows
recording.
• Do not press STOP
Audio Dubbing, or the edit points will not be
accurate.
2 4
p
.
U
.
pg. 13) can be
Y
to go a little beyond the beginning
T
to view the recorded tape,
s
at exactly the point where
s
.
U
.
Y
or FF
U
during Insert Editing or
P
.
d
, press and
T
. When
a
during Audio Dub-