VISIT OUR WEBSITE TO: Get usage advice, brochures, trouble shooter, service and repair information: www.zanussi.com/support SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damage that are the result of incorrect installation or usage.
Do not change the specification of this appliance. • The operating water pressure (minimum and maximum) must be • between 0.5 (0.05) / 8 (0.8) bar (MPa) Follow the maximum number of 13 place settings. • If the supply cord is damaged, it must be replaced by the •...
cable need to be replaced, this must be carried • Dishwasher detergents are dangerous. Follow out by our Authorised Service Centre. the safety instructions on the detergent • Connect the mains plug to the mains socket packaging. only at the end of the installation. Make sure that •...
PRODUCT DESCRIPTION The graphics below is just a general product overview. For more detailed information, refer to other chapters and/or documents provided with the appliance. Upper spray arm Rinse aid dispenser Lower spray arm Detergent dispenser Filters Cutlery basket Rating plate Lower basket Salt container Upper basket...
CONTROL PANEL On/Off button/Reset button Extra Power button Delay start button AUTO programme button Indicators Programme buttons INDICATORS Indicator Description Rinse aid indicator. It is on when the rinse aid dispenser needs refilling. Refer to "Before first use". Salt indicator. It is on when the salt container needs refilling. Refer to "Before first use".
Page 7
The appliance senses the degree of soil and the temperature and quantity of water as well as the amount of dishes in the baskets. It adjusts the wash duration. PROGRAMMES OVERVIEW Programme Type of load Degree of soil Programme phases Options 30 min •...
Water (l) Energy (kWh) Duration (min) 1) 2) Programme AUTO 9 - 12.8 0.694 - 1.223 120 - 170 Machine Care 8.8 - 10.7 0.46 - 0.562 1) The pressure and the temperature of the water, the variations of the mains supply, the options, the quan- tity of dishes and the degree of soil can change the values.
SETTING MODE • For the settings with two values (on and off), the light is either on (= the setting is How to enter setting mode on) or off (= the setting is off). • For the settings with multiple values (levels), You can enter setting mode before starting a the light flashes.
BEFORE FIRST USE 1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3. Fill the rinse aid dispenser. 4.
DAILY USE 1. Open the water tap. HOW TO SELECT AND START THE PROGRAMME PRE-RINSE 2. Press and hold until the appliance is 1. To select Pre-rinse, press and hold 30 min for activated. 3 seconds. 3. Fill the salt container if it is empty. 4.
During the countdown, it is not possible to change consumption and the programme duration. After the programme selection. closing the door, the appliance continues from the point of interruption. When the countdown is complete, the programme starts. If the door is opened for more than 30 seconds during the drying phase, the HOW TO CANCEL THE DELAY START WHILE running programme ends.
• In areas with hard and very hard water, we • The filters are clean and correctly installed. recommend to use basic dishwasher detergent • The cap of the salt container is tight. (powder, gel, tablets containing no additional • The spray arms are not clogged.
When the appliance senses the need for cleaning, the indicator is on. Start the Machine Care programme to clean the appliance interior. How to start the Machine Care programme Before starting the Machine Care programme, clean the filters and spray arms.
CLEANING THE LOWER SPRAY ARM We recommend to clean the lower spray arm regularly to prevent soil from clogging the holes. Clogged holes can cause unsatisfactory washing results. 1. To remove the lower spray arm, pull it upwards. 5. Make sure that there are no residues of food or soil in or around the edge of the sump.
TROUBLESHOOTING Refer to the below table for information on possible WARNING! Improper repair of the problems. appliance may pose a danger to the With some problems, the lights related to the safety of the user. Any repairs must be programme buttons flash intermittently to indicate a performed by qualified personnel.
Problem and alarm code Possible cause and solution Small leak from the appliance • The appliance is not levelled. Loosen or tighten the adjustable door. feet (if applicable). • The appliance door is not centred on the tub. Adjust the rear foot (if applicable).
Page 19
Problem Possible cause and solution Poor drying results. • Tableware was left for too long inside the closed appliance. Activate AirDry to set the automatic opening of the door and to improve the drying performance. • There is no rinse aid or the dosage of rinse aid is not suffi- cient.
Problem Possible cause and solution Limescale deposits on the table- • The level of salt is low, check the refill indicator. ware, on the tub and on the in- • The cap of the salt container is loose. side of the door. •...