Table of Contents
Advertisement
USING THE UNIT SAFELY
WARNING
Use only the supplied AC adaptor and the
correct voltage
Be sure to use only the AC adaptor
supplied with the unit. Also, make
sure the line voltage at the installation
matches the input voltage specified on the AC
adaptor's body. Other AC adaptors may use a
different polarity, or be designed for a different
voltage, so their use could result in damage,
malfunction, or electric shock.
IMPORTANT NOTES
Placement
¹ Depending on the material and temperature of the surface on which
you place the unit, its rubber feet may discolor or mar the surface.
Repairs and Data
¹ Before sending the unit away for repairs, be sure to make a backup of
the data stored within it; or you may prefer to write down the needed
information. Although we will do our utmost to preserve the data
stored in your unit when we carry out repairs, in some cases, such
as when the memory section is physically damaged, restoration of
the stored content may be impossible. Roland assumes no liability
concerning the restoration of any stored content that has been lost.
Additional Precautions
¹ Any data stored within the unit can be lost as the result of equipment
failure, incorrect operation, etc. To protect yourself against the
irretrievable loss of data, be sure to make a backup of the data stored
within it; or you may prefer to write down the needed information.
¹ Roland assumes no liability concerning the restoration of any stored
content that has been lost.
¹ Never strike or apply strong pressure to the display.
¹ Do not use connection cables that contain a built-in resistor.
Caution Regarding Radio Frequency Emissions
¹ The following actions may subject you to penalty of law.
– Disassembling or modifying this device.
– Removing the certification label affixed to the back of this device.
– Using this device in a country other than where it was purchased
8
CAUTION
Handle the ground terminal carefully
If you remove the screw from the ground
terminal, be sure to replace it; don't
leave it lying around where it could
accidentally be swallowed by small children.
When refastening the screw, make that it is
firmly fastened, so it won't come loose.
Intellectual Property Right
¹ ASIO is a trademark and software of Steinberg Media Technologies
GmbH.
¹ The Bluetooth® word mark and logos are registered trademarks owned
by Bluetooth SIG, Inc. and any use of such marks by Roland is under
license.
¹ This Product uses the Source Code of μT-Kernel under T-License 2.0
granted by the T-Engine Forum (www.tron.org).
¹ This product includes third party open source software.
Copyright © 2009-2021 ARM Limited. All rights reserved.
Licensed under the Apache License, Version 2.0 (the "License");
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Copyright © 2016 Freescale Semiconductor, Inc.
Copyright © 2016-2021 NXP. All rights reserved.
Licensed under the BSD-3-Clause;
You may obtain a copy of the License at
https://opensource.org/licenses/BSD-3-Clause
Copyright © 2020 Amazon.com, Inc. or its affiliates. All Rights Reserved.
Licensed under the MIT license
https://opensource.org/licenses/mit-license.php
This product's software is based in part on the work of the Independent
JPEG Group.
¹ Roland and BOSS are either registered trademarks or trademarks of
Roland Corporation in the United States and/or other countries.
¹ Company names and product names appearing in this document are
registered trademarks or trademarks of their respective owners.
CAUTION
Precautions concerning use of phantom
power supply
Always turn the phantom power off
when connecting any device other than
condenser microphones that require
phantom power. You risk causing damage if you
mistakenly supply phantom power to dynamic
microphones, audio playback devices, or other
devices that don't require such power. Be sure
to check the specifications of any microphone
you intend to use by referring to the manual
that came with it.
(This instrument's phantom power: 48 V DC,
10 mA Max)
Advertisement
Table of Contents
