JVC HR-S9400EE Instructions Manual page 17

Index Sea rch
Your recorder automatically marks
index codes at the beginning of
each recording. This function gives
you quick access to any one of 9
index codes in either direction.
N O TE:
Before starting, make sure the
recorder is in the Stop mode.
ACTIVATE IN DEX SEARCH
1
Press PU SH JO G
control. " ™ 1" or " £ 1" is displayed on screen
and search begins in the corresponding direction.
● To access index codes 2 through 9, press
or repeatedly until the correct index number is
displayed.
Ex.: To locate the beginning of B from the current
position, press PUSH J OG
To locate the beginning of D from the current
position, press PU SH J O G
● When the specified index code is located, playback
begins automatically.
Insta nt ReV iew
Simply by pressing a single button, the recorder power comes
on, rewinds, and begins playback of the last timer-recorded
programme. If you have several programmes recorded, you can
easily access any of them.
N O TE:
Before starting, make sure that the recorder is off and that the
Timer mode is disengaged.
ACTIVATE IN STAN T
REVIEW
1
Press REVIEW . The recorder power comes on and the
recorder searches for the index code indicating the start
of the last timer-recorded programme. Once it's found,
playback begins automatically.
The front display panel tells you how many programmes
have been recorded. If you have, for example, 3
programmes, " REVIEW" and "3" appear and blink. To
watch the first of the 3 programmes, press REVIEW three
times. The recorder searches and begins playback
automatically. You can access a programme as far as 9
index codes away from the current tape position.
N O TE:
Instant ReView is not possible while the recorder is in the Timer
mode.
Downloaded from: https://www.usersmanualguide.com/
( ™ or £ ) on the remote
or
PU SH JO G
twice.
once.
Current position
A B C D E F
–2 –1 1 2 3
Index number
M ESECAM Pla yba ck
Your recorder is equipped with MESECAM circuitry that can
£ 2
play back MESECAM tapes. MESECAM is the designation for
tapes with SECAM signals that have been recorded on a
MESECAM-compatible PAL video recorder.
LO AD A CASSETTE
1
Insert a cassette recorded in MESECAM.
EN GAGE MESECAM PLAYBACK
MO DE
2
Press M ESECAM PLAY-
BACK ; the current setting
will be displayed on the
screen for about 5 seconds.
Pressing M ESECAM
PLAYBACK while the
screen shows the display
changes the setting.
● The setting will remain
effective even though
you turn on/off the recorder or you insert/eject the
cassette.
● The setting cannot be changed during search, still,
frame-by-frame playback or slow motion mode.
ST ART PLAYBACK
3
Press PLAY .
N O TES:
● You can change the "MESECAM P .B." setting even though
"O.S.D." is set to "OFF".
● When you play back a PAL or SECAM tape, be sure to set
"MESECAM P.B." to "OFF".
Repea t Pla yba ck
Your video recorder can
automatically play back
the whole tape 20 times
repeatedly.
ST ART PLAYBACK
1
Press PLAY .
ACTIVATE REPEAT PLAYBACK
2
Press PLAY and hold for over 5 seconds, then release.
● The Play indicator ( $ ) on the display panel blinks
slowly.
● The tape plays 20 times automatically, and then
stops.
STO P PLAYBACK
3
Press STO P at any time to stop playback.
N O TE:
Pressing PLAY , REW , FF or PAU SE also stops Repeat Playback.
17
EN
MESECAM P. B. ON