Insignia NS-STR514-C Quick Setup Manual

Congratulations on your purchase of a high-quality Insignia product. Your
NS-STR514 / NS-STR514-C represents the state-of-the-art in stereo receiver
design and is designed for reliable and trouble-free performance.
Package contents
• Receiver • Indoor AM and FM antennas
• Remote control • User Guide
• AAA batteries (2) • Quick Setup Guide
Setting up your receiver
• Install your receiver on a stable flat surface. Position your receiver so that it has a direct
line of sight to the remote control.
• Do not expose your receiver to extreme temperature or humidity.
• Avoid placing your receiver on a hot surface such as on top of other hot running
equipment. Make sure that there is adequate ventilation to your receiver.
Connecting the antennas
1 Assemble the AM antenna.
2 To connect the indoor AM antenna, press the GND and AM Loop levers, insert the ends GND and AM Loop levers insert the ends
of the wires, then release the levers. Make sure that only the bare, stripped wire is
inserted in the jack.
Indoor AM antenna
Indoor FM
antenna
3 Connect the indoor FM antenna to the FM jack on the back of the receiver.
4 Later, move the antennas until you get the best reception of your favorite AM and FM
stations.
Before using your new product, please read these instructions to prevent any damage.
Connecting audio-only devices
Back panel
TV
CD player
3.5 mm audio cable
(not included)
Connecting devices with video
1 Connect the cable from the Audio Out jack on the audio device to the L/R AUX IN (1 or 2)
jacks on the receiver.
2 Connect the video cable(s) (component, composite, HDMI, or coaxial) from the output
jack on the video device to the appropriate input jack on your TV.
NOTE: For more information on connecting a recording device, such as a VCR or tape deck, refer to
the User Guide.
TV
Video cable
DVR/DVD/Blu-ray
Stereo Receiver with Bluetooth | NS-STR514 / NS-STR514-C
Connecting speakers
NOTE: If you have only one pair of speakers, connect them to
the SPEAKER A terminals.
1 Turn the terminal cap to loosen it.
2 Insert the bare wire into the terminal and tighten the
terminal cap to securely connect it. Make sure that
you strip the wire adequately so that none of the wire
insulation is under the terminal.
3 Make sure cables are secure by lightly pulling on them.
NOTE: Connect speakers by matching the channel (left and
right) and polarity (+ and -).
If the sound is unnatural and lacks bass, the speaker polarity
is incorrect.
Connecting headphones
• Insert a 1/4" headphone plug into the headphone jack on the front of the receiver.
H appears on the display, and sound can be heard from the headphones.
NOTE: When you plug headphones into the receiver, the external speakers are turned off.
Connecting the power
• Plug the power cord into an AC outlet.
Quick Setup Guide
Speaker A
Using your receiver
Right Left
1 Install the remote control batteries.
2 Press ON/STANDBY on the remote control or the receiver to turn the receiver on.
The STANDBY indicator is off. Press again to put the receiver into standby mode and the
STANDBY indicator lights red.
Right Left
Speaker B
3 Turn on the devices connected to the receiver.
4 If you connected a video device, such as a DVD or Blu-ray player:
• Select that device's input on the TV.
• Turn your TV speakers off if you only want the audio to come from your receiver.
5 Press the INPUT button on the receiver or press one of the input buttons on the remote
control for the input source you want. Each time you press the button on the receiver, the
display changes to reflect the input selected.
6 Start playback on the device you selected.
7 Press SPEAKER A or SPEAKER B on the remote to turn the corresponding speakers on.
SPK A, SPK B, SPK AB, or SPK OFF appears on the display and sound can be heard from
the speakers.
8 Turn the VOLUME dial on the receiver or press the VOLUME +/- buttons on the remote to
adjust the sound level.
-OR-
Press MUTE on the remote to turn the sound off. MUTE flashes on the display.
Press MUTE again to turn the sound back on.
Connecting Bluetooth
1 Select BT AUDIO as the input source by pressing the BLUETOOTH button on the remote
control or the INPUT button on the receiver repeatedly until BT AUDIO appears. PAIRING
will be shown on the display and the Bluetooth indicator will blink.
2 Navigate to your device's Bluetooth settings, turn on Bluetooth, then search for available
devices.
a. For iPad/iPhone/iPod touch:
i. From the home page, touch Settings > General >Bluetooth.
b. For Android Phone/Tablet:
i. From your smart phone/tablet home page, touch Settings >Wireless and networks.
ii. Touch to activate Bluetooth, then touch Bluetooth settings.
c. For a PC or Mac, you can find these instructions in the documentation that came with
your computer or operating system.
3 On your Bluetooth device, select "NS-STR514" from the device list.
4 If a PIN code is requested, enter "0000."
5 When pairing is completed, "CONNECTED" is shown on your receiver display and the
Bluetooth indicator turns on.
NOTE: To control playback, use the Bluetooth playback buttons on your remote control.
For additional information on using your receiver, refer to the User Guide.