Auto Sp→Ep Timer; Auto Timer - JVC HR-J6006UM Instructions Manual

Auto SP → EP Timer
If, when recording in SP mode, there is not enough tape to record
the entire program, the VCR automatically switches to EP mode
to allow complete recording. This feature is especially handy
when recording a program of more than 2 hours in length.
For Example . . .
Recording a program of 140 minutes in length onto a 120-
minute tape
Approximately 110 minutes
SP mode
Make sure you set "AUTO SP→EP TIMER" to "ON" at the
Function screen before the timer recording starts.
ACCESS MAIN MENU
SCREEN
1
Press MENU.
ACCESS FUNCTION SET
SCREEN
2
Move the highlight bar (arrow) to "FUNCTION SET" by
pressing CH 5 ∞ or % fi, then press OK or
SELECT AUTO SP → EP
TIMER SET MODE
3
HR-J6006UM
FUNCTION
B.E.S.T.
PICTURE CONTROL

AUTO TIMER

SUPERIMPOSE
=AUTO SP = EP TIMER
VIDEO STABILIZER
NEXT PAGE
SELECT WITH (5,∞) AND (OK)
PRESS (MENU) TO END
Move the highlight bar (arrow) to "AUTO SP→EP
TIMER" by pressing CH 5 ∞ or % fi, then press OK or
to set to "ON".
RETURN TO NORMAL
SCREEN
4
Press MENU.
NOTES:
● If you have programmed the VCR to timer-record 2 or more
programs, the second program and those thereafter may not
fit on the tape if you set the Auto SP → EP Timer mode to
"ON". In this case, make sure the mode is not engaged, then
set the tape speed manually during timer programming.
● In order to ensure that the recording fits on the tape, this feature
may leave a slight non-recorded section at the end of the tape.
● There may be some noise at the point on the tape where the
VCR switches from SP to EP mode.
● The Auto SP → EP Timer feature is not available during ITR
(Instant Timer Recording), and the feature will work with the
following tapes: T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120.
Downloaded from: https://www.usersmanualguide.com/
Approximately 30 minutes
EP mode
Total 140 minutes
HR-J4406UM
FUNCTION
ON B.E.S.T.
AUTO PICTURE CONTROL
OFF AUTO TIMER
ON SUPERIMPOSE
ON =AUTO SP = EP TIMER
ON VIDEO STABILIZER
SELECT WITH (5,∞) AND (OK)
PRESS (MENU) TO END
Auto Timer
When the Auto Timer is set to ON the timer is automatically
engaged when the VCR's power is turned off. It is automatically
disengaged when the VCR is powered back on.
ACCESS MAIN MENU
SCREEN
1
Press MENU.
ACCESS FUNCTION SET
SCREEN
2
Move the highlight bar (arrow) to "FUNCTION SET" by
pressing CH5∞ or % fi, then press OK or
SELECT AUTO TIMER SET
MODE
3
B.E.S.T.
PICTURE CONTROL
=AUTO TIMER
.
SUPERIMPOSE
AUTO SP = EP TIMER
VIDEO STABILIZER
NEXT PAGE
SELECT WITH (5,∞) AND (OK)
PRESS (MENU) TO END
Move the highlight bar (arrow) to "AUTO TIMER" by
pressing CH5∞ or % fi, then press OK or
ON
"ON" or "OFF".
AUTO
OFF
RETURN TO NORMAL
ON
ON
ON SCREEN
4
Press MENU.
NOTE:
For safety, when "AUTO TIMER" is set to "OFF", all other VCR
functions are disabled while the Timer mode is engaged. To
disengage the timer, press ‰ ‰ ‰ ‰ ‰ .
HR-J6006UM HR-J4406UM
FUNCTION
ON B.E.S.T.
AUTO PICTURE CONTROL
OFF =AUTO TIMER
ON SUPERIMPOSE
OFF
AUTO SP = EP TIMER
ON VIDEO STABILIZER
SELECT WITH (5,∞) AND (OK)
PRESS (MENU) TO END
27
EN
.
FUNCTION
ON
AUTO
OFF
ON
OFF
ON
to set to