Searching For Your Code; Setting Up Other Components - One for All URC-5650 Cinema 5 User Manual

SEARCHING FOR YOUR CODE

If your TV, VCR or Cable Converter does not respond to the Cinema 5 after
trying all of the codes listed for your brand, or if your brand is not listed at all, try
searching for your code. For example, after trying all of the codes for your TV,
you still cannot get the Cinema 5 to operate your TV, then:
1. Turn on your TV.
2. Press TV and release. Press and hold SETUP until the
Cinema 5 's red light blinks twice, then release SETUP.
9 - 9 - 1
9 - 9 - 1
3. Press 9 - 9 - 1.
4. Slowly alternate between pressing POWER* and TV until
your TV turns OFF. Make sure that the Cinema 5 is aimed at
your TV during the search. You may have to press this
sequence of buttons (POWER* then TV) up to
100 times to search the entire library of codes.
5. When your TV turns OFF, press and release SETUP to
lock in the code for your TV. Your Cinema 5 is now
programmed to operate your TV.
*Some VCR, LD or DVD player do not have POWER key on the original remote.
If so turn on the VCR/DVD/LD player manually, insert a tape or CD and start
playing. Start the code search process and use STOP key instead of POWER.
When the device responds, press and release the SETUP key to lock in the
code. RED LED will blink twice.
NOTE: To search for the codes of your other components, repeat Steps 1
through 5, only substitute the appropriate device key (VCR, DVD/LD, RCVR or
CBL/SAT) for the component you are searching for.
RETRIEVE THE CODES PROGRAMMED IN THE Big Easy HT Plus
If you have set up the Cinema 5 using the "SEARCHING FOR YOUR CODE"
procedure, you may want to figure out which four-digit code is operating your
equipment. Use this procedure after you have set up your components to find
out which four-digit code is operating your equipment. For example, to find out
which code is operating your TV after setting up your TV using the "SEARCH-
ING FOR YOUR CODE" procedure:
1. Press TV and release. Press and hold SETUP until the
Cinema 5 's red light blinks twice, then release SETUP.
9 - 9 - 0
9 - 9 - 0
2. Press 9 - 9 - 0.
1
1
3. For the first digit of your four-digit code, press 1 and count
the number of times the red light (LED) blinks on the
Cinema 5 . If the light does not blink when you press the
number 1, the digit is zero.
2
2
4. For the second digit, press 2 and count the number of
times the red light (LED) blinks on the Cinema 5 . If
the light does not blink when you press the number 2, the
digit is zero.
5. For the third digit, press 3 and count the number of times
3
3
the red light (LED) blinks on the Cinema 5 . If the light
does not blink when you press the number 3, the digit
is zero.
6. For the fourth and final digit, press 4 and count the number
4
4
of times the red light (LED) blinks on the Cinema 5 .
If the light does not blink when you press the number 4, the
digit is zero. Now you have your four-digit code.
NOTE: To find out the code for your other components, repeat Steps 1
through 6, only substitute the appropriate device key (VCR, DVD/LD,
RCVR or CBL/SAT) for the component code you wish to learn.

SETTING UP OTHER COMPONENTS

In addition to the components labeled on the device keys (TV, VCR, DVD/LD,
CBL/SAT, etc.), the Cinema 5 can also operate the following components:
Cassette Decks, Video Accessories, Amplifier and Miscellaneous Audio
Components (Graphic Equalizers and Digital Music Service Boxes).
The Setup Codes for these components can be accessed under the following
device keys:
Cassette Decks: Use the VCR Key
Video Accessories: Use the CBL/SAT Key
Amplifier: Use the RCVR Key
Miscellaneous Audio: Use the RCVR Key
For example, to set up a Cassette Player on the VCR key:
1. Turn on your Cassette Player and insert a tape.
2. Press VCR and release. Press and hold SETUP until the
Cinema 5' s red light blinks twice, then release
SETUP.
3. Enter the first four-digit Cassette Player code listed for your
brand in the "Setup Codes For Audio Cassettes" section. If
you perform this procedure correctly, the red light will blink
twice when you enter the final digit of your code.
4. Aim the Cinema 5 at your Cassette Player and
press PL (Play). Your Cassette Player should play your
tape. If your Cassette Player does not respond, repeat
steps 2-4, trying each code listed for your brand until you
find the one that operates your Cassette Player.
5. Your Big Easy HT Plus is now programmed to operate your
Cassette Player.
Remember, if you want to use your Cinema 5 to operate your Cassette Player,
press the VCR key first.
Setup Codes For Audio Cassette Decks
Aiwa 0029, 0197
Carver 0029
Denon 0076
Harman/Kardon 0182
JVC 0244, 0273
Kenwood 0070
Magnavox 0029
Marantz 0029
Onkyo 0135, 0282
Optimus 0027, 0220
Philips 0029
Pioneer 0027, 0099, 0220
Sansui 0029
Sony 0170, 0243, 0291
Technics 0229
Victor 0273
Wards 0027
Yamaha 0094, 0097
Setup Codes For Video Accessories
Archer 0160
GC Electronics 0160
Jebsee 0160
Rabbit 0081
RadioShack 0160
Roctec 0456
SuperGuide 0169
TeleCaption 0171
Setup Codes For Integrated
Carver 0269
Curtis Maths 0300
Denon 0160
GE 0078
JVC 0331
Linn 0269
Luxman 0165
Magnavox 0269
Marantz 0269, 0321
Nakamichi 0321
Optimus 0013, 0300, 0395
Panasonic 0308
Pioneer 0013, 0300
Realistic 0395
Amplifier/Preamplifiers/Amplifiers