Notas Relativas A Este Manual De Instruccio- Nes - Stihl TSA 230 Instruction Manual

español
A kickback is the result of the incorrect or faulty
use of the electrical power tool. It can be preven-
ted by taking suitable measures, as described
below.
a) Hold the electrical power tool firmly and
make sure your body and arms are in a posi-
tion so that you can catch the kickback
forces. Always use the additional handle, if
available, to maintain the best possible con-
trol of kickback forces or reactive torques
during start-up. The operator can control the
kickback and reactive forces by taken suita-
ble precautions.
b) Never place your hand near the rotating tool
bits. The tool bit can move across your hand
in the event of a kickback.
c) Avoid the area in front of and behind the
rotating abrasive wheel. The kickback drives
the electrical power tool in a direction that is
opposite to the movement of the abrasive
wheel at the blockage site.
d) Work with great care around corners, sharp
edges, etc. Prevent tool bits of the workpiece
from recoiling and jamming. The rotating tool
bit tends to jam when it hits corners, sharp
edges or if it ricochets. This results in the
loss of control or kickback.
e) Do not use a chain or toothed saw blade or a
segmented diamond wheel with more than a
10 mm wide slit. Such tool bits often cause
kickback or the loss of control of the electri-
cal power tool.
f) Avoid the blocking of the abrasive wheel or a
surface pressure that is too high. Do not
make cuts that are too deep. Overloading the
abrasive wheel increases its stress level and
the likelihood of skewing or blocking, and
thereby the possibility of a kickback or break-
age of the abrasive element.
g) If the abrasive wheel jams or if you interrupt
your work, switch off the machine and hold it
still until the wheel stops. Never try to
remove an abrasive wheel that is still rotating
out of the cut as this may lead to a kickback.
Determine and rectify the cause of the jam.
h) Do not switch the electrical power tool back if
it is still in the workpiece. Allow the abrasive
wheel to reach its full speed before continu-
ing carefully with the cut. Otherwise the
wheel may catch, jump out of the workpiece
or cause a kickback.
i) Support plates or large workpieces to reduce
the risk of a kickback due to a jammed abra-
64
sive wheel. Large workpieces can bend
under their own weight. The workpiece must
be supported on both sides of the wheel,
both near the cut and at the edge.
j) Be especially careful with "pocket cuts" in
existing walls or other blind areas. If the pen-
etrating abrasive wheel cuts into gas or
water pipes, electric cables or other objects,
this can cause a kickback.
Índice
1 Notas relativas a este manual de instruccio-
nes............................................................ 64
2 Indicaciones relativas a la seguridad........ 65
3 Fuerzas de reacción................................. 71
4 Técnica de trabajo.................................... 72
5 Ejemplos de aplicación............................. 73
6 Discos....................................................... 76
7 Discos de resina sintética......................... 77
8 Discos de diamante.................................. 77
9 Colocar / cambiar el disco.........................79
10 Conectar el cargador a la red eléctrica..... 80
11 Cargar el acumulador............................... 81
12 LEDs en el acumulador.............................82
13 LED en el cargador................................... 84
14 Establecer la alimentación de agua.......... 84
15 Conectar la máquina.................................84
16 Desconectar la máquina........................... 85
17 Guardar la máquina.................................. 86
18 Instrucciones de mantenimiento y conserva-
ción........................................................... 87
19 Minimizar el desgaste y evitar daños........ 87
20 Componentes importantes........................88
21 Datos técnicos.......................................... 89
22 Subsanar irregularidades de funciona-
miento....................................................... 90
23 Indicaciones para la reparación................ 91
24 Gestión de residuos.................................. 92
25 Declaración de conformidad UE............... 92
26 Declaración de conformidad UKCA.......... 92
27 Indicaciones de seguridad generales para
herramientas eléctricas............................. 93
1 Notas relativas a este
manual de instrucciones
Este manual de instrucciones se refiere a una
tronzadora de acumulador STIHL, llamada tam-
bién máquina a motor o máquina en este manual
de instrucciones.
0458-707-9821-C