Emerson Rosemount Oxymitter 4000 Reference Manual page 191

July 2018
This declaration is issued under the sole responsibility of the manufacturer:
Rosemount Inc., 8200 Market Blvd., Chanhassen, MN 55317 USA
The product,
Oxygen Analyzers:
to which this declaration relates, is in conformity with relevant Union harmonization legislation:
(2014/30/EU) EMC Directive
(2014/35/EU) Low Voltage Directive
(2014/68/EU) Pressure Equipment Directive
This equipment has been designed and manufactured with sound engineering practices in accordance with Article 4,
Paragraph 3 of the PED
(2014/34/EU) ATEX Directive
OXT4CNF, OXT5C, OXT5CNF, OXT4CDR, OXT4CDRNF, 6A00094G05 & 6A00094G06
Provisions of the directive fulfilled by the equipment:
Equipment Group II category 2 G Ex d IIB+H2 T4 Gb (-40°C ≤ Ta ≤ 70°C) for Integral Assembly or Remote Probe
Equipment Group II category 2/- G Ex d IIB+H2 T4 Gb/- (-40°C ≤ Ta ≤ 70°C) for Integral Assembly or Remote Probe without
flame arrestor
Equipment Group II category 2 G Ex d e IIB+H2 T5 Gb (-40°C ≤ Ta ≤ 70°C) for Split Architecture Remote Electronics
Special Conditions for Safe Use:
1. Process temperature shall not exceed 115°C at mounting flange location
2. Non-flame arrestor probe versions "NF" must have the probe tube mounted in Safe Area.
3. When probe tube is mounted in Explosive Areas using flame arrestor end to complete the assembly, calibration lines
that travel in and out of the equipment bringing reference gas, must not contain a pressure higher than 1.1 times the
atmospheric pressure; these calibration lines shall not contain pure oxygen, acetylene, or combustible gases other than
the gases for which this application has been investigated for: Group IIB +H
4. There are no other interchangeable enclosure components.
5. Contact the original manufacturer for information of flameproof joint dimensions.
Sira14ATEX1201X
02 ATEX Q8020
Assumption of conformity is based on the application of the harmonized standards:
EN 61326-1:2013
EN 61010-1:2010
EN 60079-0:2012+A11:2013
EN 60079-1:2007
_______________________
(Signature)
Kim Freeman
(Name printed)
EU DECLARATION OF CONFORMITY
Oxymitter™ 4000, Models OXT4A, OXT4C, OXT4CNF, 6A00094G06
Oxymitter™ 5000, Models OXT5A, OXT5C, OXT5CNF, 6A00094G05
Oxymitter™ DR, Models OXT4ADR, OXT4CDR & OXT4CDRNF
(Directive applies to OXT4A,OXT5A and OXT4ADR)
(
EC-Type Examination Certificate issued by Sira (0518), Rake Lane Eccleston Chester
CH4 9JN, United Kingdom
Product Quality Assessment Notification issued by LCIE (0081), F-92260 Fontenay-
aux-Roses, Cedex, France
Electrical equipment for measurement, control and laboratory use. EMC
requirements. General requirements
Safety requirements for electrical equipment for measurement, control, and
laboratory use. General requirements
Explosive atmospheres. Equipment. General requirements. (Certified to 60079-
0:2012, meets /A11:2013 which does not have any major technical change)
Explosive atmospheres. Equipment protection by flameproof enclosures "d"
(No. 1700915)
The ATEX Directive is only valid for
Director of Global Quality
(Function name)
March 23, 2017
(Date of issue)
Rosemount Oxymitter 4000
Models OXT4C,
)
gases.
2
OXT
191