Table of Contents
Advertisement
III. Accessories
Check the accessories in the package, if any of them is missing or damaged, please contact
your supplier immediately.
User manual -------------------------------------------------- 1 pc
Test leads (red, black) ------------------------------------- 1 pair
Alligator clips (red, black) --------------------------------- 1 pair
1.5V AAA battery -------------------------------------------- 3 pcs
Tool box ------------------------------------------------------- 1 pc
Brown box ---------------------------------------------------- 1 pc
AAA Ni-MH rechargeable battery ----------------------- 3 pcs (optional)
Test probes (red, black) ----------------------------------- 1 pair
IV. Safety Information
Note the "Warning labels and sentences". A Warning identifies conditions and procedures
that are dangerous to the user and that can cause damage to the Product or the equipment
under test.
The product is designed in accordance with IEC/EN61010-1, 61010-2-032, Electromagnetic
Radiation EN61326-1 Standard, and conforms to Double Insulation, Overvoltage CAT III 1000V,
CAT IV 600V and pollution degree 2. Failure to follow operating instructions can impair the
protection provided by the product.
1. Check the product and test leads before use. Pay attention to any damage or abnormal
situation. Please stop use if test lead and casing insulation are damaged, or the LCD
displays nothing, or the product cannot work normally.
2. Before each use verify tester operation by measuring a known voltage.
3. It is forbidden to use without rear cover or battery cover set in place. Otherwise it may cause
electric shock.
4. Keep fingers behind the finger guard and never make contact with exposed wire, connector ,
input terminal not in use, or circuit being measured during measurement.
5. Do not exert AC voltage over 1000V between terminal and grounding to prevent electric
shock and product damage.
6. Use caution when working with voltages over 60V DC or 30Vrms AC.
7. Never use the tester on a circuit with frequency that exceed the rating of this tester.
8. To meet the requirements of safety standard, please use the product together with equipped
test leads and alligator clips. If test leads or alligator clips are damaged, replace a new one
which should meet IEC61010-031 standard, rated follow parameters of the product or better.
9. When the symbol "
" appears on the LCD, please replace the battery in time to ensure
measurement accuracy. Remove the battery if the product is not used for a long time.
10. Do not alter the internal wiring to avoid product damage and safety hazard.
11. Do not keep or use the product in environments with high temperature, high humidity, strong
electromagnetic field, or inflammable and explosive environments.
12. Please wipe the casing with soft cloth and neutral cleaning agent, do not use abrasives
or solvents, so as to avoid casing corrosion, product damage, and safety hazard.
5
UT219P User Manual
UT219P User Manual
V. Electrical Symbols
System
CAT III
CAT IV
VI. General Specifications
1) Overload protection voltage between input terminal and grounding: 1000V
2) Ingress protection: Ip54
3) Polarity indication: Auto
4) Overload indication: "OL" or "-OL"
5) Error caused by testing area: An additional error of ± 1.0% of reading can occur when the
source to be measured is not placed at the center of the clamp jaws for current measurement.
6) Drop proof: 1 m
7) Maximum jaw opening: 80mm in diameter
8) Maximum diameter of measured conductor: 75 mm
9) Power supply:3 X 1.5V AAA batteries (type: LR03) or 3 X 1.2V rechargeable Ni-MH batteries
10) Auto power off: The product powers off automatically after 15 minutes of inactivity.
11) Dimensions: 295 mm*118mm*50mm
12) Weight: About 630g (including battery)
13) Operating altitude: 2000 m
14) Intended use: Indoor user
15) Operating temperature and humidity: 0°C~30°C (≤80%RH); 30°C~40°C (≤75%RH);
40°C~50°C (≤45%RH)
16) Storage temperature and humidity: -20°C~+60°C (≤80%RH)
17) EMC: Under radio frequency field of 1V/m, overall accuracy = specified accuracy + 5%
of range. Under radio frequency field over 1V/m, there is no specified specification.
Description
Application around and removal from UNINSULATED HAZARDOUS LIVE
conductors is permitted
AC (Alternating Current)
Bluetooth communication
Double insulated
Grounding
Warning
Conform to European Union standards
Conform to UL STD 61010-1, 61010-2-032
Certified to CSA STD C22.2 NO. 61010-1, 61010-2-032
UKCA certification mark
Applicable to test and measure the circuit connected with the power
distribution part of building's low-voltage MAINS installation.
Applicable to test and measure the circuit connected with the
power supply of building's low-voltage MAINS installation.
The product conforms to the identification requirement of WEEE directive.
Do not place equipment and its accessories in the trash.
6
Advertisement
Table of Contents
