Table of Contents
Advertisement
English
nOTE: The worklight is for lighting the immediate work surface
and is not intended to be used as a flashlight.
Drill Operation
WARNING: TO REDUCE THE RISK OF PERSONAL
INJURY, ALWAYS ensure workpiece is anchored or
clamped firmly. If drilling thin material, use a wood
"back‑up" block to prevent damage to the material.
1. Select the desired speed/torque range using the
speed selector to match the speed and torque to the
planned operation.
2. For WOOD, use twist bits, spade bits, power auger bits or
hole saws. For METAL, use high-speed steel twist drill bits
or hole saws. Use a cutting lubricant when drilling metals.
The exceptions are cast iron and brass which should be
drilled dry.
3. Always apply pressure in a straight line with the bit. Use
enough pressure to keep the drill bit biting, but do not push
hard enough to stall the motor or deflect the bit.
4. Hold tool firmly with both hands to control the twisting
action of the drill.
5. iF DRill sTAlls, it is usually because it is being
overloaded. RElEAsE TRiggER iMMEDiATElY, remove
drill bit from work, and determine cause of stalling. DO
nOT CliCK TRiggER OFF AnD On in An ATTEMPT
TO sTART A sTAllED DRill – This CAn DAMAgE
ThE DRill.
6. Keep the motor running when pulling the bit back out of a
drilled hole. This will help prevent jamming.
Screwdriver Operation
1. Select the desired speed/torque range using the speed
selector
3
to match the speed and torque of the
planned operation.
2. Insert the desired fastener accessory into the chuck as you
would any drill bit.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
The charger and battery pack are not serviceable.
C
Lubrication
Your power tool requires no additional lubrication.
10
D
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non‑metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories
WARNING: Since accessories, other than those offered
by STANLEY FATMAX, have not been tested with this
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only STANLEY
FATMAX‑recommended accessories should be used with
this product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. Products and batteries marked
w
with this symbol must not be disposed of with
normal household waste.
Products and batteries contain materials that can be
recovered or recycled, reducing the demand for raw materials.
Please recycle electrical products and batteries according to local
provisions. Further information is available at www.2helpU.com.
Rechargeable Battery Pack
This long-life battery pack must be recharged when it fails to produce
sufficient power on jobs that were easily done before. At the end of
its technical life, discard it with due care for our environment:
•
Run the battery pack down completely, then remove it from
the tool.
•
Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
COMPATIBLE
V
Ah
BATTERIES
DC
SFMCB201
18
1.5
SFMCB202
18
2.0
SFMCB204
18
4.0
SFMCB206
18
6.0
COMPATIBLE CHARGERS
SFMCB11
SFMCB12
SFMCB14
Advertisement
Table of Contents
