Table of Contents
Advertisement
Ver. 1.2 2014.04
The changed portions from
Ver. 1.1 are shown in blue.
Camera
[Recording media]
"Memory Stick XC Duo" media,
[System]
Camera type: Interchangeable lens
digital camera
Lens: E-mount lens
[Electronic viewfinder]
Type: Electronic viewfinder
[Image sensor]
Screen size: 0.5 cm (0.20 type)
Image sensor: APS-C format
Total number of dots:
(23.2 mm × 15.4 mm) CMOS
image sensor
Frame coverage: 100%
Total pixel number of image sensor:
Magnification: 0.70 × with 50 mm lens
Approx. 20 400 000 pixels
Effective pixel number of camera:
Eye point: Approx. 21 mm from the
Approx. 20 100 000 pixels
[Auto focus system]
Diopter adjustment:
System: Contrast detection system
Sensitivity range: EV0 to EV20 (at ISO
100 conversion, with F2.8 lens)
[LCD screen]
LCD panel: Wide, 7.5 cm (3.0 type)
[Exposure control]
Metering method: 1 200-segment
Total number of dots: 230 400 dots
metering by the image sensor
Metering range: EV0 to EV20 (at ISO
[Input/output terminals]
100 conversion, with F2.8 lens)
Multi/Micro USB Terminal*:
ISO sensitivity (Recommended
exposure index):
Still images: AUTO, ISO 100 –
ISO 16000
[Power]
Movies: AUTO, ISO 100 –
Battery type: Rechargeable battery
ISO 3200 equivalent
Exposure compensation:
±3.0 EV (1/3 EV step)
[Power consumption]
When using an E 18-55 mm F3.5-5.6
[Shutter]
Type: Electronically-controlled,
vertical-traverse, focal-plane type
Speed range:
Still images: 1/4 000 second to
30 seconds, BULB
Movies: 1/4 000 second to
[Others]
1/4 second (1/3 EV step),
Exif Print: Compatible
1080 60i-compatible device up to
PRINT Image Matching III:
1/30 second in AUTO mode
1080 50i-compatible device up to
DPOF: Compatible
1/25 second in AUTO mode
Dimensions (CIPA compliant)
Flash sync speed: 1/160 second
Model information table
Model
ILCE-3000K
Destination
US, CND, E, KR, BR
AEP, UK, RU, E, AUS, CH, JE
Color system
NTSC
Lens
E 18-55 mm F3.5-5.6 OSS
E 18-55 mm F3.5-5.6 OSS
• Abbreviation
AUS : Australian model
BR
: Brazilian model
CH : Chinese model
CND : Canadian model
JE
: Tourist model
KR : Korea model
RU : Russian model
ILCE-3000K/3500J_L2
SPECIFICATIONS
Mass (CIPA compliant) (Approx.):
411 g (14.5 oz) (including battery
and "Memory Stick PRO Duo"
"Memory Stick PRO Duo" media,
media)
SD card
353 g (12.5 oz) (camera only)
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
File format:
Still image: JPEG (DCF Ver. 2.0,
Exif Ver. 2.3, MPF Baseline)
201 600 dots equivalent
compliant, RAW (Sony ARW
2.3 Format)
Movie (AVCHD format): AVCHD
at infinity, –1 m
–1
(diopter)
format Ver. 2.0 compatible
Video: MPEG-4 AVC/H.264
eyepiece, 15 mm from the eyepiece
Audio: Dolby Digital 2ch
frame at –1 m
–1
(diopter)
Dolby Digital Stereo Creator
• Manufactured under license from Dolby
–4.0 m
–1
to +3.5 m
–1
(diopter)
Laboratories.
Movie (MP4 format):
Video: MPEG-4 AVC/H.264
Audio: MPEG-4 AAC-LC 2ch
TFT drive
USB communication:
Hi-Speed USB (USB 2.0)
[Flash]
Flash guide number:
USB communication
4 (in meters at ISO 100)
* Supports Micro USB compatible device.
Recycling time: Approx. 4 seconds
Flash coverage: Covering 16 mm lens
(focal length that the lens indicates)
Flash compensation:
pack NP-FW50
±2.0 EV (1/3 EV step)
Rechargeable battery pack
NP-FW50
OSS lens
Battery type: Lithium-ion battery
When using the viewfinder:
Maximum voltage: DC 8.4 V
Approx. 2.0 W
Nominal voltage: DC 7.2 V
When using an LCD screen:
Maximum charge voltage: DC 8.4 V
Approx. 1.9 W
Maximum charge current: 1.02 A
Capacity: Typical 7.7 Wh (1 080 mAh)
Minimum 7.3 Wh (1 020 mAh)
Maximum dimensions (Approx.):
31.8 mm × 18.5 mm × 45 mm
Compatible
(1 5/16 inches × 3/4 inches ×
1 13/16 inches) (W/H/D)
Mass (Approx.): 57 g (2.1 oz)
(Approx.):
128.0 mm × 90.9 mm × 84.5 mm
(5 1/8 inches × 3 5/8 inches ×
3 3/8 inches) (W/H/D)
ILCE-3500J
US, CND, E, BR
PAL
NTSC
E 18-50 mm F4-5.6
E 18-50 mm F4-5.6
CHEMICALS
Some chemicals used for servicing are highly volatile.
Their evaporation caused by improper management affects your health
and environment, and wastes resources.
Manage the chemicals carefully as follows.
•
Store chemicals sealed in a specific place to prevent from exposure
to high temperature or direct sunlight.
•
Avoid dividing chemicals into excessive numbers of small containers
to reduce natural evaporation.
•
Keep containers sealed to avoid natural evaporation when chemicals
are not in use.
•
Avoid using chemicals as much as possible. When using chemicals,
divide only required amount to a small plate from the container and
use up it.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes and
bridges.
2. Check the interboard wiring to ensure that no wires are "pinched"
or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 350°C during
repairing.
RU, E, AUS
• Do not touch the soldering iron on the same conductor of the circuit
PAL
board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
– 2 –
EXTERIOR PARTS
Be careful to the following points for plastic parts used in this unit.
•
Use a piece of cleaning paper or cleaning cloth for cleaning plastic
parts. Avoid using chemicals.
Even if you have to use chemicals to clean heavy dirt, don't use paint
thinner, ketone, nor alcohol.
•
Insert the specific screws vertically to the part when installing a
plastic part.
Be careful not to tighten screws too much.
注意
如果电池更换不当会有爆炸危险。
只能用同样类型或等效类型的电池来更换。
务必按照说明处置用完的电池。
ATTENTION AU COMPOSANT AYANT RAPPORT
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
UNLEADED SOLDER
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
•
Set the soldering iron tip temperature to 350°C approximately.
If cannot control temperature, solder/unsolder at high temperature
for a short time.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
•
Be sure to control soldering iron tips used for unleaded solder and
those for leaded solder so they are managed separately. Mixing
unleaded solder and leaded solder will cause detachment phenom-
enon.
À LA SÉCURITÉ!
Advertisement
Table of Contents
