Table of Contents
Advertisement
2-1-4. IMAGER BLOCK SECTION
ns: not supplied
151
(including CP6001 (CMOS imager)
and IS-1007 complete board)
(Note 5)
#197
161
ns
159
160
158
165
(Note 6)
Ref. No.
Part No.
Description
151
A-1954-964-A
SERVICE, MECHA DEVICE (1100)
(including CP6001 (CMOS imager) and IS-1007 complete
board) (Note 5)
152
4-430-446-01
SHEET (IS (720)), RADIATION
* 153
Selection Parts IM WASHER (A), ADJUST (Note 2, 3)
* 154
Selection Parts IM WASHER (B), ADJUST (Note 2, 3)
* 155
Selection Parts IM WASHER (C), ADJUST (Note 2, 3)
156
A-1905-698-A
MB CHARGE UNIT (762) (Note 4)
157
1-492-255-11
SHUTTER UNIT (H129)
158
A-1932-986-A
MB N HOLDER ASSY (SERVICE 762)
ILCE-3000K/3500J_L2
1
ns
#64
152
(Note 1)
153
(Note 2, 3)
#230
154
155
(Note 2, 3)
(Note 2, 3)
Imager Unit Section
2
156
(See page 2-7)
(Note 4)
162
157
(Note 7)
163
164
#64
Ref. No.
Part No.
Description
* 159
4-186-538-01
SPRING, LENS LOCK
160
X-2586-035-1
MB L LOCK PIN ASSY (762)
161
4-456-086-01
BUTTON, LENS LOCK
* 162
4-185-963-01
MB N PLATE SP (Note 7)
163
4-284-623-01
MB N PLATE (B) 755
164
4-283-999-03
MB N PLATE A (754)
165
4-188-536-01
CAP, BODY (Note 6)
#64
2-666-551-21
SCREW, TAPPING, P2
#197
4-185-990-01
MB SCREW, CHARGE UNIT FIXED
#230
4-287-434-01
TAPPING (1.7 (ECOLOGY))
DISASSEMBLY
1. Remove in numerical order (
to
) in the left figure.
1
2
#64 X 3
1
Back View
#64
Screw
#64: M1.7 X 5.0 (Tapping)
#197: M1.6 X 4.5 (Tapping)
(Silver)
(Silver)
2-666-551-21
4-185-990-01
1.6
1.7
4.5
5.0
Note
Note 1: Refer to "Assembly-3: Screw tightening sequence when
assembling the Radiation Plate (IM)" when assembling.
Note 2: The IM adjust washers (A, B, C) differ in thickness.
Make sure to return the removed IM adjust washers to origi-
nal places.
When replacing IM adjust washers, refer to "2-2. SELEC-
TION PARTS" on page 2-9.
If the original state cannot be restored due to loss of the
IM adjust washer, for example, replace the Mecha Device
(1100) (Service).
Note 3: Refer to "Assembly-4: IM Adjust Washer (A, B, C) putting
position" when assembling.
Note 4: Refer to "Assembly-5: Screw tightening sequence when
assembling the MB Charge Unit" when assembling.
Note 5: Precautions for Replacement of the Mecha Device
(1100) (Service).
As Mecha Device (1100) (Service) may be damaged by
static electricity from its structure, handle it carefully like for
the MOS IC.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
Note 6: The Mecha Device (1100) (Service) includes a protective
Body Cap.
This part is supplied only with the Mecha Device (1100)
(Service).
Note 7: Refer to "Assembly-6: Apply grease on the MB N Plate SP"
when assembling.
2-6
#230 X 3
2
Back View
#230
#230: M1.7 X 4.0 (Tapping)
(Black)
4-287-434-01
1.7
4.0
Advertisement
Table of Contents
