Byron DB401E - Wirefree Portable Door Chime Kit Instructions

SET UP

1. Using a small flat screwdriver, insert into the locking clip and gently twist. The back plate will unclip from the Bell Push.
2. Insert the 23A battery (Supplied) into the battery holder, making sure the Positive/Negative terminals match the internal markings.
3. Remove the battery cover and insert 3 X 1.5V size 'AA'/LR6 batteries, making sure the positive/negative terminals match the internal markings.
4. Press the Bell Push within 30 seconds, the chime will ring to confirm that the Bell Push has been paired to the Chime.
5. Test the Chime in the intended location, as internal walls and surfaces may reduce operating range. DO NOT mount onto metallic surfaces.
6. High/Low volume switch

WALL MOUNTING YOUR BELL PUSH

7.1 Using back plate as template.
7.2 Make sure UP arrow points UP.
7.3 Mark and drill holes.
7.4 Insert wall plugs and attach to wall using screws provided.
7.5 Clip the Bell Push on to the back plate making sure the Bell Push 'Clicks' in to place.
7.6 Place the Door Chime, within the operating range (50M). Transmission of the wire free signal through walls, doors and ceilings etc, may reduce the operating range.

CHANGING PUSH BATTERY

8.1: Remove back plate from the Bell Push
8.2: Remove old battery from the holder
8.3: Replace with new '23A' battery
8.4: Insert the 23A battery into the battery holder, making sure the Positive/Negative terminals match the internal markings.
8.5: Test Chime Kit

ATTENTION:
Avoid positioning the Bell Push/Chime on or directly near metallic surfaces as this may reduce the operation range.

UPVC Door Frames:
When positioning the bell push onto a UPVC door, always check the operating performance before final installation, internal metal frame of the door may affect performance.

Tip: Try adjusting the location of the Bell Push slightly to the Left/Right or place on an external wall.

Note: the appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction. Children should be supervised to ensure that they do not play with the appliance.

TROUBLE SHOOTING

In case of the door chime does not sound, please check the followings:

1. Flat batteries in either push button or door chime.
2. Wrong battery polarity in either push button or door chime.
3. For plug-in door chimes make sure the socket is switched on.
4. Bell push and door chime are not paired together, see setup guide.
5. Materials in between the bell push & chime will reduce the operating range, move the door chime closer to the bell push
6. Wire free devices can be affected by external sources e.g. wirefree home alarms or power transformers/adapter
7. Make sure the volume switch is in the HIGH or LOW position and not in the MUTE position

Type R2 Device - device where the sound output is created by the initial operation of the control and where the period of sound output continues for the designed duration irrespective of condition of the control.

There are no serviceable parts, do not repair. The appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. Children should be supervised to ensure that they do not play with the appliance.

SPECIFICATION

Bell Push: DBT
Power: 1 x 23A 12V DC Battery (Included)
IP44 Weather Resistant

Portable Door Chime: DB301/A
Power: 3 x 'AA'/LR6 1.5V Batteries total: 4.5V DC (not included)
Range: 50 Metres
Indoor Use Only

Smartwares declares that this appliance complies with the main essential requirements of the R&TTE directive, 1999/5/CE. The complete declaration of conformity is available on request at:

Smartwares Safety & Lighting
Byron House,
34, Sherwood Rd,
Aston Fields,
Bromsgrove
B60 3DR
UK
www.chbyron.eu/byronsupport
Tel: 0845 2301231 (UK)
10-4 Mon-Fri, except Thurs 12:30-4
Local call charges apply