Quick Start; Notes On Installation; Video Input; Aux Input - NAD C350 Owner's Manual

QUICK START

1. Connect the speakers to the rear Speaker sockets and sources
to the relevant rear input sockets.
2. Plug in the AC power cord.
3. Press the POWER button to turn the NAD C350 on.
4. Press the required input selector.

NOTES ON INSTALLATION

Your NAD C350 should be placed on a firm, level surface. Avoid
placing the unit in direct sunlight or near sources of heat and
damp. Allow adequate ventilation. Do not place the unit on a soft
surface like a carpet. Do not place or it in an enclosed position,
such a bookcase or cabinet, that may impede the air-flow through
the ventilation slots. Make sure the unit is switched off before
making any connections.
The RCA sockets on your NAD C350 are colour coded for
convenience. Red and white are Right and Left audio respectively,
and yellow for NAD Link. Use high quality leads and sockets for
optimum performance and reliability. Ensure that leads and
sockets are not damaged in any way and all sockets are firmly
pushed home.
For best performance, use quality speaker leads of 16 gauge
(1.5mm) thickness or more. If the unit is not going to be used for
some time, disconnect the plug from the AC socket.
Should water get into your NAD C350, shut off the power to the
unit and remove the plug from the AC socket. Have the unit
inspected by a qualified service technician before attempting to
use it again. Do not remove the cover, there are no user-
serviceable parts inside. Use a dry soft cloth to clean the unit.
If necessary, lightly dampen the cloth with soapy water. Do not use
solutions containing benzol or other volatile agents.
REAR PANEL CONNECTIONS (FIGURE 1)
GB
1. NAD LINK IN, OUT
The NAD-Link connector is used to pass commands from other
units fitted with NAD-Link connectors. This allows centralised
control of a complete system, and also allows some of the basic
functions of other NAD components (such as a tuner, CD player or
cassette-deck) also equipped with NAD-Link to be controlled with
the amplifier's remote control. To function with such other units,
connect the C350's NAD-Link Out to the NAD-Link In on the other
unit. NAD-Link connectors can be daisy-chained, IN to OUT, so
that a whole system can be controlled from the remote control
facilities of one unit.
NOTES: It is advisable not to connect NAD-Link if these units that
have their own built-in remote control command receiver and are
postioned together, in direct view from the remote control
handset. If you are unsure, try operating the products without
NAD-Link first; If the unit responds to the remote control
command, it will not be necessary to connect NAD-Link. Never
loop the last unit back to the first NAD unit in the NAD-Link chain.
Unplug all units from the mains before connecting or
disconnecting NAD-Link.
4
NAD C350 Stereo Integrated Amplifier
2. DISC INPUT
Input for additional line level input signals such as CD, Mini Disc
player or the output signal from a step-up amplifier for a
turntable. Use a twin RCA-to-RCA lead to connect the auxiliary
unit's left and right 'Audio Outputs' to this input.
3. CD INPUT
Input for a CD or other line-level signal source. Use a twin RCA-
to-RCA lead to connect the CD player's left and right 'Audio
Outputs' to this input. The NAD C350 only accepts analogue
signals from your CD player.

4. VIDEO INPUT

Input for the audio signal from a stereo VCR (or stereo
TV/Satellite/Cable receiver) or other line-level audio source.
Using twin RCA-to-RCA leads, connect to the left and right 'Audio
Out' of the unit to these inputs. Note: These are audio inputs only.

5. AUX INPUT

Input for additional line level input signals such as another CD
player. Use a twin RCA-to-RCA lead to connect the auxiliary unit's
left and right 'Audio Outputs' to this input.
6. TUNER INPUT
Input for a Tuner or other line-level signal source. Use a twin RCA-
to-RCA lead to connect the Tuner left and right 'Audio Outputs' to
this input.
7. TAPE 2 IN, OUT
Connections for analogue recording and playback to an audio
tape recorder of any type. Using twin RCA-to-RCA leads, connect
to the left and right 'Audio Output' of the tape machine to the TAPE
2 IN sockets for playback and tape monitoring. Connect the left
and right 'Audio Input' of the tape machine to the TAPE 2 OUT
sockets for recording.
8. TAPE 1 IN, OUT
Connections for analogue recording and playback to a secondary
audio tape recorder of any type. Using twin RCA-to-RCA leads,
connect to the left and right 'Audio Output' of the tape machine to
the TAPE 1 IN sockets for playback and tape monitoring. Connect
the left and right 'Audio Input' of the tape machine to the TAPE 1
OUT sockets for recording.
9. PRE OUT 1
The NAD C350 allows for the connection multiple power
amplifiers. If you are using a single stereo power amplifier, use the
PRE OUT 1 sockets. If you are using a pair of power amplifiers
specifically for Bi-amping, use the sockets to connect the power
amplifier with the lowest gain of the pair. Use a twin RCA-to-RCA
lead to connect to the left and right 'Audio Input' of the Power
amp to the PRE OUT 1 sockets.
10. PRE OUT 2
Connections to an external power amplifier or processor, such as
a surround-sound decoder. In normal use these should be
connected to the Main-In sockets (No. 11) with the links
supplied. To connect your NAD C350 to external processor or
amplifier sections first remove these links. Use a twin RCA-to-RCA
lead to connect to the left and right 'Audio Input' of the Power
amp or processor to the Pre Out 2 sockets.