NAD C356BEE Owner's Manual
  1. Manuals
  2. Brands
  3. NAD Manuals
  4. Amplifier
  5. C356BEE
  6. Owner's manual

NAD C356BEE Owner's Manual

Hide thumbs Also See for C356BEE:
Table of Contents

Advertisement

Quick Links

See also: Service Manual , Owner's Manual
C 356BEE
®
Stereo Integrated Amplifier
Owner's Manual

Advertisement

Table of Contents
loading

Related Manuals for NAD C356BEE

Summary of Contents for NAD C356BEE

  • Page 1 C 356BEE ® Stereo Integrated Amplifier Owner’s Manual...

  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS FOR LATER USE. 14 Outdoor Antenna Grounding - If an outside antenna or cable system FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE is connected to the product, be sure the antenna or cable system is AUDIO EQUIPMENT.
  • Page 3 Changes or modifications to this equipment not expressly approved by 23 Heat - The product should be situated away from heat sources such as NAD Electronics for compliance could void the user’s authority to operate radiators, heat registers, stoves or other products (including amplifiers) this equipment.

  • Page 4: Notes On Environmental Protection

    Serial no.: ........NAD is a trademark of NAD Electronics International, a division of Lenbrook Industries Limited...

  • Page 5: Getting Started

    3 Set the rear panel POWER switch to the “ON” setting. The Standby LED consult your NAD audio/video specialist for advice on providing adequate airflow. indicator embedded around the bezel of the STANDBY button will illuminate amber and the C 356BEE goes to standby mode.

  • Page 6: Identification Of Controls

    IDENTIFICATION OF CONTROLS FRONT PANEL 1 STANDBY BUTTON: With the rear panel POWER switch set to ON 5 MP SOCKET: Using a 3.5mm stereo plug, connect into this socket the position, press this button to switch ON the C 356BEE from standby audio output of a Media Player.
  • Page 7 IDENTIFICATION OF CONTROLS FRONT PANEL 8 INPUT SELECTORS: These buttons select the active input to the 11 BALANCE: The BALANCE control adjusts the relative levels of the C 356BEE and the signal sent to the loudspeakers, headphones and the left and right speakers. The 12 o’clock position provides equal level to PRE OUT sockets.

  • Page 8: Rear Panel

    If an optional Modular Design Construction (MDC) module is installed, the DISC input socket is disabled and the MDC source is selected as the active input. All NAD products with IR IN/IR OUT features are fully compatible with the C 356BEE. For non-NAD models, please check with your other 8 AUX INPUT: Input for additional line level input signals such as another product’s service specialists with respect to its compatibility with the C 356BEE’s IR features.

  • Page 9: To Make A Recording

    REAR PANEL 9 TAPE 2 IN/OUT: Connections for analog recording and playback to 14 SOFT CLIPPING™: Enables NAD’s proprietary Soft Clipping circuitry a tape recorder of any type. Using twin RCA-to-RCA leads, connect on all channels. At [ON] position, Soft Clipping gently limits the output the left and right “Audio Output”...
  • Page 10 REAR PANEL 19 MDC CLASSIC UPGRADE SLOT: Remove cover to install the Consult with your NAD dealer on how to procure the PP 375 and optional Modular Design Construction (MDC) module. An example its consequent installation to the C 356BEE. Check out also the NAD...
  • Page 11 SR 8 REMOTE CONTROL USING THE SR 8 REMOTE CONTROL The SR 8 remote control handset handles the key functions of the C 356BEE as well as other NAD Stereo Receivers, Integrated Amplifiers and Preamplifiers. It has additional controls to remotely operate NAD CD Players, AM/FM Tuners and dedicated AM/FM/DB Tuners.
  • Page 12 NAD CD Player models; check the owner’s manual of your NAD CD Player for control button compatibility. You can also load the applicable NAD code library to this device so that it can be made compatible with your other NAD equipment. Refer to the section below about “USING THE SR 8 REMOTE CONTROL LIBRARY”...
  • Page 13 SR 8 REMOTE CONTROL USING THE SR 8 REMOTE CONTROL LIBRARY The SR 8 can store a different library of default NAD codes for each of its DEVICE SELECTOR “pages. ” If the original default library does not control your NAD CD player, DVD player, or other component, follow the procedure below to change the library code.

  • Page 14: Troubleshooting

    REFERENCE TROUBLESHOOTING CONDITION POSSIBLE CAUSES POSSIBLE SOLUTIONS No sound. • Mains power cord unplugged or power not • Check if mains power cord is plugged in and switched ON. power switched ON. • TAPE MONITOR selected. • De-select TAPE MONITOR mode. •...

  • Page 15: Specifications

    REFERENCE SPECIFICATIONS PREAMPLIFIER SECTION LINE LEVEL INPUT, PRE OUT 20 Hz – 20 kHz, CCIF IMD, SMPTE IMD, DIM 100 <0.005 % at 2 V out Signal-to-Noise Ratio >106 dB (IHF; A-weighted, ref. 500 mV out, unity gain) >114 dB (A-weighted, ref. 2 V out, Volume maximum) >92 dB (ref.

  • Page 16: Overall Specifications

    REFERENCE SPECIFICATIONS PHONO SECTION (WITH OPTIONAL PP 375 INSTALLED) MM/MC IN, PRE OUT Input impedance - MC 100 ohms (R) 180 pF (C) 47 kohms (R) 180 pF (C) Input sensitivity for 80 W in 8 ohms - MC 0.38 mV 1 kHz 5.0 mV 1 kHz Input sensitivity for 1 W in 8 ohms - MC...
  • Page 18 All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited. No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International.

Table of Contents