MEMORY CHANNELS
In memory channels, you can store frequencies and
related data that you often use. Then you need not
reprogram those data every time. You can quickly
recall a programmed channel through simple
operation. A total of 400 memory channels are
available for storing the frequencies, modes and
other operating conditions of the A and B-bands.
SIMPLEX & REPEATER OR
ODD-SPLIT MEMORY CHANNEL?
You can use each memory channel as a simplex &
repeater channel or an odd-split channel. Store only
one frequency to use as a simplex & repeater
channel or two separate frequencies to use as an
odd-split channel. Select either application for each
channel depending on the operations you have in
mind.
Simplex & repeater channels allow:
•
Simplex frequency operation
•
Repeater operation with a standard offset
(if an offset direction is stored)
Odd-split channels allow:
•
Repeater operation with a non-standard offset
Note: Not only can you store data in memory channels, but you can
also overwrite existing data with new data.
The data listed below can be stored in each memory
channel:
P
a
a r
m
t e
r e
R
e
c
e
v i
e
f
e r
q
u
e
n
y c
T
a r
n
s
m
i
f t
e r
q
u
e
n
y c
T
o
n
e
f
e r
q
u
e
n
y c
T
o
n
e
O
N
C
T
C
S
S
f
e r
q
u
e
n
y c
C
T
C
S
S
O
N
D
C
S
c
o
d
e
D
C
S
O
N
O
f
s f
t e
i d
e r
t c
o i
n
O
f
s f
e
f t
e r
q
u
e
n
y c
R
e
v
e
s r
e
O
N
F
e r
q
u
e
n
y c
s
e t
p
s
z i
e
M
e
m
o
y r
c
h
a
n
n
l e
o l
k c
o
t u
M
e
m
o
y r
c
h
a
n
n
l e
n
a
m
e
F
N I
E
u t
n
n i
g
O
N
M
o
d
e
s
e
e l
t c
o i
n
Yes: Can be stored in memory.
N/A: Cannot be stored in memory.
Note: The transmit frequency must be on the same band as the
receive frequency band (Odd-split channel).
i S
m
l p
x e
&
O
d d
S -
p
t i l
R
e
e p
t a
r e
Y
e
s
Y
e
s
Y
e
s
Y
e
s
Y
e
s
Y
e
s
Y
e
s
Y
e
s
Y
e
s
Y
e
s
Y
e
s
Y
e
s
Y
e
s
Y
e
s
Y
e
s
Y
e
s
N
A /
Y
e
s
N
A /
Y
e
s
N
A /
Y
e
s
Y
e
s
Y
e
s
Y
e
s
Y
e
s
Y
e
s
Y
e
s
Y
e
s
Y
e
s
Y
e
s
STORING SIMPLEX FREQUENCIES OR
STANDARD REPEATER FREQUENCIES
1 Press [VFO].
2 Turn the Tuning control or press [ ]/ [ ] to select
your desired frequency in the amateur radio
bands.
• You can also directly enter desired frequency
using the keypad {page 7}.
3 If storing a standard repeater frequency, select the
following data:
• Offset direction {page 12}
• Tone function, if necessary {page 13}
• CTCSS/ DCS function, if necessary
{pages 28, 29}
If storing a simplex frequency, you may select
other related data (CTCSS or DCS settings, etc.).
4 Press [F].
• A memory channel number appears and blinks.
• " " indicates the current channel is empty; " "
appears if the channel contains data.
• Memory channel number L0/U0 ~ L9/U9
{page 23}, I–0 ~ I–9 {page 20}, and Pr1 and
Pr2 {page 25} are reserved for other functions.
5 Turn the Tuning control or press [ ]/ [ ] to select
the memory channel in which you want to store
the data.
6 Press [MR] ([ ] or [MNU]) to store the data to the
channel.
STORING ODD-SPLIT REPEATER FREQUENCIES
Some repeaters use a receive and transmit frequency
pair with a non-standard offset. If you store two
separate frequencies in a memory channel, you can
operate on those repeaters without programming the
offset frequency and direction.
1 Store the desired receive frequency and related
data by the procedure given for simplex or
standard repeater frequencies {above}.
2 Turn the Tuning control or press [ ]/ [ ] to select
the desired transmit frequency.
3 Press [F].
4 Turn the Tuning control or press [ ]/ [ ] to select
the memory channel you programmed in step 1.
5 Press [PTT]+[MR] ([PTT]+[ ] or [PTT]+[MNU]).
• The transmit frequency is stored in the memory
channel.
Note:
When you recall an odd-split memory channel, "+" and "–" appear
on the display. To confirm the transmit frequency, press [REV].
When you revise only the transmission frequency for the odd-split
channel, the frequency step size must be the same as the
original odd-split channel memory data.
15