Multitech MT1932ZDXI Command Reference Manual page 64

Interface Configuration Commands .................55
L
Leased Line Operation – &L ............................15
Line feed character – S4 ..................................37
Load Factory Settings – &F..............................14
Local Callback Inactivity Timer – #CBI ............35
Local Flow Control Selection – \Q....................19
Long Break $LB ...............................................32
M
Manufacturer Identification Request – +GMI ...28
MNP Error Correction.......................................18
Model Identification Request – +GMM.............28
Modulation Handshake – N..............................11
Modulation Reporting Control – +MR= ............30
Modulation Selection – +MS= ..........................30
Monitor Speaker Mode – M..............................10
N
Number of Rings – S0......................................37
O
Online BPS Speed – $MB................................32
Online command mode ......................................6
Online Data Character Echo – F........................9
P
Pause Length – S8...........................................37
Protocol Result Code – \V................................19
Pulse Dial Make-to-Break Ratio – &P ..............15
Pulse Dialing – P..............................................11
R
Remote Configuration
Escape Character – S9 ................................37
Remote Configuration Escape sequence –
%%%ATMTSMODEM ..................................34
Repeat Last Command – A/...............................7
Request ID Info – I ...........................................10
Reset and Recall Stored Profile – Z.................13
Result Code Format – V...................................12
Result Code Options – W.................................12
Result codes ......................................................6
Result Codes....................................................40
Result Codes Enable/Disable – Q ...................11
Return Online to Data Mode – O .....................11
Revision Request – +GMR ..............................28
Ring Priority vs. AT Command Priority – $RP .33
Ringback Goes Away Timer – VRA= ...............49
Ringback Never Appeared Timer – +VRN=.....49
ROM Checksum...............................................10
S
Select Analog Source/Destination – +VLS= ....48
Select Maximum MNP Block Size command – \A
......................................................................17
Select Result Code & Call Monitor Progress – X
......................................................................13
Multi-Tech Systems, Inc. AT Commands for the MultiModem & SocketModem MT9234 Series (S000434D)
Select Tone Dialing – T ................................... 12
Select V.42bis or V.44 Data Compression –
+DCS............................................................ 23
Select Voice Compression Method – +VSM= . 51
Select Voice Mode – +FCLASS=8................... 44
Self Test commands – &T ............................... 16
Send V.8bis Signal and/or Message – +A8T... 23
Send Voice Tones – +VTS= ............................ 45
Serial Port Baud Rate – $SB ........................... 33
Set AT Command Mode Timer – %DT ............ 21
Set Callback Security – Direct Connect Enable
%H................................................................ 21
Set Register Value – Sr= ................................. 12
Set Sleep Mode – S24..................................... 37
Set the Volume for Transmitted Voice Samples
– +VGT=....................................................... 46
Set Up Error Control Parameters – +ESA ....... 27
Silence Detection Sensitivity – +VSD= ............ 50
sleep mode – S89 ............................................ 39
Speed
Maximum – S37 ........................................... 38
S-registers
S2 – Escape Sequence................................ 37
S-Registers ...................................................... 37
S0 – Sets Number of Rings.......................... 37
S1 – Counts Rings ....................................... 37
S10 – Carrier Loss Disconnect Time ........... 37
S11 – Dialing Tones..................................... 37
S24 – Set Sleep Mode ................................. 37
S28 – V.34 Modulation................................. 37
S3 – Carriage Return ................................... 37
S30 – Inactivity Timer................................... 37
S35 – V.25 Calling Tone .............................. 37
S36 – Error Control ...................................... 37
S37 – Maximum Speed................................ 38
S38 – Downstream Data Rate ..................... 38
S4 – Line Feed Character ............................ 37
S43 – Testing and Debugging...................... 38
S48 – Error Control ...................................... 39
S5 – Backspace Character .......................... 37
S6 – Wait Time for Dail Tone ....................... 37
S7 – Abort Timer .......................................... 37
S8 – Pause Length....................................... 37
S89 – Standby.............................................. 39
S9 – Remote Configuration Escape Character
.................................................................. 37
Standby mode delay time – S89...................... 39
Start Voice Transmission Process – +VTX...... 46
Store Callback Password – #CBN ................... 35
Store Current Configuration – &W ................... 17
Store Dialing Location and Number – &Z ........ 17
Store Setup Password – #S=........................... 34
T
Testing and Debugging – S43 ......................... 38
Transmit Break – \B ......................................... 17
Transmit Flow Control Threshold – +ITF=....... 30
U
Unsolicited Voice Mode Result Codes ............ 58
Index
64